Lunkerbildung in Schweissnähten = Bubble formation in welding seamsBONTEN, C; MÜLLER-JUREK, J; SCHMACHTENBERG, E et al.Plastverarbeiter. 1995, Vol 46, Num 8, pp 26-28, issn 0032-1338Article

Mechanism of weld line formation in injection molding of plasticsENIKEEV, A. V; KAZANKOV, Yu. V; MIRONOV, V. A et al.Chemical and petroleum engineering. 1999, Vol 35, Num 1-2, pp 118-123, issn 0009-2355Article

Les mécanismes de formation et de cohésion des lignes de soudure de flux dans les pièces injectées en matière plastique = Cohesion and formation mecanisms of weldlines in polymer injection molding processDebondue, Eric; Pabiot, José.1997, 266 p.Thesis

Improving the Water Resistance of Linear Vibration-Welded Wood JointsMANSOURI, H. R; OMRANI, P; PIZZI, A et al.Journal of adhesion science and technology. 2009, Vol 23, Num 1, pp 63-70, issn 0169-4243, 8 p.Article

Improving weldline strengths of injection moulded parts by ultrasonic oscillationLIU, S.-J; LIN, K.-Y; TSAI, S.-K et al.Plastics, rubber and composites. 2008, Vol 37, Num 1, pp 23-28, issn 1465-8011, 6 p.Article

Effect of an obstacle during processing on the weld line of injection-molded glassy polystyrene: Microhardness studyNGUYEN-CHUNG, T; MENNIG, G; BOYANOVA, M et al.Journal of applied polymer science. 2004, Vol 92, Num 5, pp 3362-3367, issn 0021-8995, 6 p.Article

Polypropylene/montmorillonite nanocomposites prepared by the delamination of the fillerPOZSGAY, A; PAPP, L; FRATER, T et al.Progress in colloid & polymer science. 2001, pp 120-125, issn 0340-255X, isbn 3-540-41946-2Conference Paper

Influence of Machine Setting and Wood Parameters on Crack Formation in Scots Pine Joints Produced by Linear Friction WeldingVAZIRI, Mojgan; LINDGREN, Owe; PIZZ, Antonio et al.Journal of adhesion science and technology. 2012, Vol 26, Num 18-19, pp 2189-2197, issn 0169-4243, 9 p.Article

Analysis for diving regulator applying local heating mechanism of vapor chamber in insert molding processWANG, Jung-Chang; LI, Ai-Tsung; TSAI, Yu-Pin et al.International communications in heat and mass transfer. 2011, Vol 38, Num 2, pp 179-183, issn 0735-1933, 5 p.Article

Flow disturbance in polymer melt behind an obstacleNGUYEN-CHUNG, T; PLICHTA, C; MENNIG, G et al.Rheologica acta. 1998, Vol 37, Num 3, pp 299-305, issn 0035-4511Article

Effect of processing on weld line strength in five thermoplasticsSELDEN, R.Polymer engineering and science. 1997, Vol 37, Num 1, pp 205-218, issn 0032-3888Article

Factors affecting the shape of weld lineOHOKA, S; TAKADA, K; KIDOKORO, K et al.Kobunshi ronbunshu (Tokyo). 1996, Vol 53, Num 6, pp 339-344, issn 0386-2186Article

INFLUENCE OF NATURE AND TYPE OF FLAW ON THE PROPERTIES OF A NATURAL RUBBER COMPOUNDNGOLEMASANGO, Frederick E; O'CONNOR, Chris; MANLEY, John et al.RubberChem 2008. 2008, isbn 1-8473-5077-1 978-1-8473-5077-0, 1Vol, Q1-Q8Conference Paper

Designing plastic parts for the gas-assisted injection-moulding techniqueJOHANNABER, F; KONEJUNG, K.Polimeri (Zagreb). 1993, Vol 14, Num 6, pp 247-252, issn 0351-1871Article

Injection molding-induced morphology of thermoplastic polymer blendsZHONG, Gan-Ji; LI, Zhong-Ming.Polymer engineering and science. 2005, Vol 45, Num 12, pp 1655-1665, issn 0032-3888, 11 p.Article

Weld-line sensitivity of injected amorphous polymersDEBONDUE, E; FOURNIER, J.-E; LACRAMPE, M.-F et al.Journal of applied polymer science. 2004, Vol 93, Num 2, pp 644-650, issn 0021-8995, 7 p.Article

Development of weld line strength in injection-molded poly(methyl methacrylate)O, A. K; BRIEN-SOUCY; BARRY, C. M. F et al.The Journal of injection molding technology. 2000, Vol 4, Num 3, pp 152-158, issn 1533-905XArticle

Microhardness study across the weld line in doubly injection-molded glassy polymersGARCIA GUTIERREZ, M. C; RUEDA, D. R; BALTA CALLEJA, F. J et al.Journal of materials science letters. 1999, Vol 18, Num 15, pp 1237-1238, issn 0261-8028Article

Flow analysis of the weld line formation during injection mold filling of thermoplasticsNGUYEN-CHUNG, Tham.Rheologica acta. 2004, Vol 43, Num 3, pp 240-245, issn 0035-4511, 6 p.Article

Investigations on the weldline tensile strength of thin-wall injection molded partsREAN DER CHIEN; CHEN, Shia-Chung; PENG, Hsin-Shu et al.Journal of reinforced plastics and composites. 2004, Vol 23, Num 6, pp 575-588, issn 0731-6844, 14 p.Article

Determination of welding sequence : a neural net approachFUKUDA, S; YOSHIKAWA, K.Engineering analysis with boundary elements. 1990, Vol 7, Num 2, pp 78-82, issn 0955-7997, 5 p.Article

Investigation the effects of obstacle geometries and injection molding parameters on weld line strength using experimental and finite element methods in plastic injection moldingOZCELIK, Babur; KURAM, Emel; MUSTAFA TOPAL, M et al.International communications in heat and mass transfer. 2012, Vol 39, Num 2, pp 275-281, issn 0735-1933, 7 p.Article

Advanced Injection Molding Mold and Molding Process for Improvement of Weld Line Strengths and Isotropy of Glass Fiber Filled Aromatic Polyester LCPKOPONEN, Matti; ENQVIST, Jouni; NGUYEN-CHUNG, Tham et al.Polymer engineering and science. 2008, Vol 48, Num 4, pp 711-716, issn 0032-3888, 6 p.Article

Dynamic Simulation of Fusion Process and Analysis of Flow FieldSUPEI ZHENG; JIE OUYANG; LING ZHANG et al.Journal of reinforced plastics and composites. 2007, Vol 26, Num 17, pp 1781-1792, issn 0731-6844, 12 p.Article

Effect of weld lines on the injection moulding of structural foams. II mechanical propertiesLEDUC, Simon; RODRIGUE, Denis.Cellular polymers. 2006, Vol 25, Num 2, pp 63-83, issn 0262-4893, 21 p.Article