Prediction of the effect of speed on motion errors in hydrostatic guidewaysZHIWEI WANG; WANHUA ZHAO; YAOLONG CHEN et al.International journal of machine tools & manufacture. 2013, Vol 64, pp 78-84, issn 0890-6955, 7 p.Article

Anti-clogging performance evaluation and parameterized design of emitters with labyrinth channelsJUN ZHANG; WANHUA ZHAO; YIPING TANG et al.Computers and electronics in agriculture. 2010, Vol 74, Num 1, pp 59-65, issn 0168-1699, 7 p.Article

Integrating cross-sectional imaging based reverse engineering with rapid prototypingZHENKAI LIU; LIHUI WANG; BINGHENG LU et al.Computers in industry. 2006, Vol 57, Num 2, pp 131-140, issn 0166-3615, 10 p.Article

Rapid Prediction of Hydraulic Performance for Emitters with Labyrinth ChannelsJUN ZHANG; WANHUA ZHAO; BINGHENG LU et al.Journal of irrigation and drainage engineering. 2013, Vol 139, Num 5, pp 414-418, issn 0733-9437, 5 p.Article

The Maximum Allowable Misalignment in Hydrodynamic Rolling Hybrid BearingsDUN LU; WANHUA ZHAO; BINGHENG LU et al.Journal of engineering for gas turbines and power. 2014, Vol 136, Num 8, issn 0742-4795, 082501.1-082501.6Article

Investigation of growth properties of patterned and aligned carbon nanotubes for field emitterHONGZHONG LIU; YONGSHENG SHI; YUCHENG DING et al.Microelectronic engineering. 2009, Vol 86, Num 11, pp 2236-2240, issn 0167-9317, 5 p.Article

Static characteristics of a new hydrodynamic―rolling hybrid bearingDUN LU; WANHUA ZHAO; BINGHENG LU et al.Tribology international. 2012, Vol 48, pp 87-92, issn 0301-679X, 6 p.Article

New Method of Hydraulic Performance Evaluation on Emitters with Labyrinth ChannelsJUN ZHANG; WANHUA ZHAO; BINGHENG LU et al.Journal of irrigation and drainage engineering. 2011, Vol 137, Num 12, pp 811-815, issn 0733-9437, 5 p.Article

Development of a step micro-imprint lithography toolHONGBO LAN; YUCHENG DING; HONGZHONG LIU et al.Journal of micromechanics and microengineering (Print). 2007, Vol 17, Num 10, pp 2039-2048, issn 0960-1317, 10 p.Article

Review of the wafer stage for nanoimprint lithographyHONGBO LAN; YUCHENG DING; HONGZHONG LIU et al.Microelectronic engineering. 2007, Vol 84, Num 4, pp 684-688, issn 0167-9317, 5 p.Article

Growth of patterned and aligned carbon nanotube bundles on micro-structured substrateYONGSHENG SHI; YUCHENG DING; HONGZHONG LIU et al.Applied surface science. 2009, Vol 255, Num 17, pp 7713-7718, issn 0169-4332, 6 p.Article

Web-based quotation system for stereolithography partsHONGBO LAN; YUCHENG DING; JUN HONG et al.Computers in industry. 2008, Vol 59, Num 8, pp 777-785, issn 0166-3615, 9 p.Article

Numerical and experimental study on hydraulic performance of emitters with arc labyrinth channelsJUN ZHANG; WANHUA ZHAO; ZHENGYING WEI et al.Computers and electronics in agriculture. 2007, Vol 56, Num 2, pp 120-129, issn 0168-1699, 10 p.Article

Fabrication and mechanical properties of UV-curable glass fiber-reinforced polymer-matrix compositeYUGANG DUAN; YANJUN WANG; YIPING TANG et al.Journal of composite materials. 2011, Vol 45, Num 5, pp 565-572, issn 0021-9983, 8 p.Article

Thermodynamic analysis of a new combined cooling, heat and power system driven by solid oxide fuel cell based on ammonia-water mixtureSHAOLIN MA; JIANGFENG WANG; ZHEQUAN YAN et al.Journal of power sources (Print). 2011, Vol 196, Num 20, pp 8463-8471, issn 0378-7753, 9 p.Article

Distortion reduction by load release for imprint lithographyHANSONG LI; YUCHENG DING; YIPING TANG et al.Microelectronic engineering. 2006, Vol 83, Num 3, pp 485-491, issn 0167-9317, 7 p.Article

A motor-piezo actuator for nano-scale positioning based on dual servo loop and nonlinearity compensationHONGZHONG LIU; BINGHENG LU; YUCHENG DING et al.Journal of micromechanics and microengineering (Print). 2003, Vol 13, Num 2, pp 295-299, issn 0960-1317, 5 p.Article

Fabrication of micro-structures on a PVDF/TiO₂ nano-composite film using photocatalytic lithographyNINGLI AN; HONGZHONG LIU; YUCHENG DING et al.Applied surface science. 2012, Vol 258, Num 12, pp 5052-5055, issn 0169-4332, 4 p.Article

Research on the cast molding process for high quality PDMS moldsXIANGDONG YE; HONGZHONG LIU; YUCHENG DING et al.Microelectronic engineering. 2009, Vol 86, Num 3, pp 310-313, issn 0167-9317, 4 p.Article

Imprint template fabrication based on glass wet etching using a soft etching maskQUANDAI WANG; YUGANG DUAN; BINGHENG LU et al.Journal of micromechanics and microengineering (Print). 2006, Vol 16, Num 3, pp 564-570, issn 0960-1317, 7 p.Article

Thermal shock induced nanocrack as high efficiency surface conduction electron emitterBANGDAO CHEN; HONGZHONG LIU; HONGTAO WANG et al.Applied surface science. 2011, Vol 257, Num 21, pp 9125-9128, issn 0169-4332, 4 p.Article

Investigation of ink transfer in a roller-reversal imprint processWEITAO JIANG; HONGZHONG LIU; YUCHENG DING et al.Journal of micromechanics and microengineering (Print). 2009, Vol 19, Num 1, issn 0960-1317, 015033.1-015033.8Article

A novel overlay process for imprint lithography using load release and alignment error pre-compensation methodJINYOU SHAO; YUCHENG DING; YIPING TANG et al.Microelectronic engineering. 2008, Vol 85, Num 1, pp 168-174, issn 0167-9317, 7 p.Article

Two-Step curing method for demoulding in UV nanoimprint lithographyWEITAO JIANG; YUCHENG DING; HONGZHONG LIU et al.Microelectronic engineering. 2008, Vol 85, Num 2, pp 458-464, issn 0167-9317, 7 p.Article

Investigation of pattern coating on mould roller in roller-reversal imprint processWEITAO JIANG; HONGZHONG LIU; YUCHENG DING et al.Microelectronic engineering. 2009, Vol 86, Num 12, pp 2412-2416, issn 0167-9317, 5 p.Article