Parameterization of randomly measured points for least squares fitting of B-spline curves and surfacesWEIYIN MA; KRUTH, J. P.Computer-aided design. 1995, Vol 27, Num 9, pp 663-675, issn 0010-4485Article

NURBS curve and surface fitting for reverse engineeringMA, W; KRUTH, J.-P.International journal, advanced manufacturing technology. 1998, Vol 14, Num 12, pp 918-927, issn 0268-3768Article

Investigation of laser and process parameters for Selective Laser ErosionYASA, E; KRUTH, J.-P.Precision engineering. 2010, Vol 34, Num 1, pp 101-112, issn 0141-6359, 12 p.Article

A CAPP system for nonlinear process plansKRUTH, J. P; DETAND, J.CIRP annals. 1992, Vol 41, Num 1, pp 489-492, issn 0007-8506Article

Development of a Closed Scanline Loop Ccanning (CSLS) as an iterative digitizing strategy for continuous scanning probesKRUTH, J.-P; BAGDJA, A.European journal of mechanical and environmental engineering. 2001, Vol 46, Num 4, pp 207-215, issn 1371-6980Article

Optimization and dynamic adaptation of the cutter inclination during five-axis milling of sculptured surfacesKRUTH, J.-P; KLEWAIS, P.CIRP annals. 1994, Vol 43, Num 1, pp 443-448, issn 0007-8506Article

The dynamics of a moving sheet of liquid, part II. experimentsGILIO, M; AL-BENDER, F; KRUTH, J.-P et al.European journal of mechanics. B, Fluids. 2005, Vol 24, Num 5, pp 572-585, issn 0997-7546, 14 p.Article

A simulation model for direct selective laser sintering of metal powdersWANG, X. C; KRUTH, J. P.International conference on computational structures technologyInternational conference on engineering computational technology. 2000, pp 57-71, isbn 0-948749-69-5Conference Paper

An operation planning system for multi-axis milling of sculptured surfacesLAUWERS, B; KRUTH, J. P; DEJONGHE, P et al.International journal, advanced manufacturing technology. 2001, Vol 17, Num 11, pp 799-804, issn 0268-3768Article

Modelling of radiation transfer in metallic powders at laser treatmentGUSAROV, A. V; KRUTH, J.-P.International journal of heat and mass transfer. 2005, Vol 48, Num 16, pp 3423-3434, issn 0017-9310, 12 p.Article

The dynamics of a moving sheet of liquid, part I. derivation of the 2D equations of motionGILIO, M; AL-BENDER, F; KRUTH, J.-P et al.European journal of mechanics. B, Fluids. 2005, Vol 24, Num 5, pp 555-571, issn 0997-7546, 17 p.Article

Self-calibration method and software error correction for three-dimensional coordinate measuring machines using artefact measurementsKRUTH, J. P; VANHERCK, P; DE JONGE, L et al.Measurement. 1994, Vol 14, Num 2, pp 157-167, issn 0263-2241Article

Optimal and collision free tool posture in five-axis machining through the tight integration of tool path generation and machine simulationLAUWERS, B; DEJONGHE, P; KRUTH, J. P et al.Computer-aided design. 2003, Vol 35, Num 5, pp 421-432, issn 0010-4485, 12 p.Article

Bedryfsorganizatie: Werkvoorbereiding toor flexibele werkplaatsorganizatie = Organisation d'entreprise: Préparation du travail en vue d'une organisation flexible sur les lieux du travail = Firm management: Work planning for flexible workplace organizationDETAND, J; KRUTH, J. P.Het ingenieursblad. 1992, Vol 61, Num 5, pp 41-48, issn 0020-1235Article

Direct selective laser sintering of hard metal powders: Experimental study and simulationWANG, X. C; LAOUI, T; BONSE, J et al.International journal, advanced manufacturing technology. 2002, Vol 19, Num 5, pp 351-357, issn 0268-3768Article

Fundamentals of selective laser melting of alloyed steel powdersROMBOUTS, M; KRUTH, J. P; FROYEN, L et al.CIRP annals. 2006, Vol 55, Num 1, pp 187-192, issn 0007-8506, 6 p.Conference Paper

Computed tomography for dimensional metrologyKRUTH, J. P; BARTSCHER, M; CARMIGNATO, S et al.CIRP annals. 2011, Vol 60, Num 2, pp 821-842, issn 0007-8506, 22 p.Conference Paper

Advanced techniques for die and mold manufacturingALTAN, T; LILLY, B. W; KRUTH, J. P et al.CIRP annals. 1993, Vol 42, Num 2, pp 707-716, issn 0007-8506Article

Micro-CT-based improvement of geometrical and mechanical controllability of selective laser melted Ti6Al4V porous structuresVAN BAEL, S; KERCKHOFS, G; MOESEN, M et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2011, Vol 528, Num 24, pp 7423-7431, issn 0921-5093, 9 p.Article

A geometrical model of the cut in five-axis milling accounting for the influence of tool orientationAGSON GANI, E; KRUTH, J. P; VANHERCK, P et al.International journal, advanced manufacturing technology. 1997, Vol 13, Num 10, pp 677-684, issn 0268-3768Article

Machining of steel with sialon ceramics : influence of ceramic and workpiece composition on tool wearVLEUGELS, J; JACOBS, P; KRUTH, J. P et al.Wear. 1995, Vol 189, Num 1-2, pp 32-44, issn 0043-1648Article

Microstructure and mechanical properties of a novel β titanium metallic composite by selective laser meltingVRANCKEN, B; THIJS, L; KRUTH, J.-P et al.Acta materialia. 2014, Vol 68, pp 150-158, issn 1359-6454, 9 p.Article

Correcting steady-state temperature influences on coordinate measuring machinesKRUTH, J.-P; VAN DEN BERGH, C; VANHERCK, P et al.Journal of manufacturing systems. 2001, Vol 19, Num 6, pp 365-374, issn 0278-6125Article

Development of technology and strategies for the machining of ceramic components by sinking and milling EDMLAUWERS, B; KRUTH, J.-P; BRANS, K et al.CIRP annals. 2007, Vol 56, Num 1, pp 225-228, issn 0007-8506, 4 p.Conference Paper

Page / 2