Dimensional measurement data analysis, Part 2 : Minimum zone evaluationCHOI, W; KURFESS, T. R.Journal of manufacturing science and engineering. 1999, Vol 121, Num 2, pp 246-250, issn 1087-1357Article

Uncertainty of extreme fit evaluation for three-dimensional measurement data analysisWONCHEOL CHOI; KURFESS, T. R.Computer-aided design. 1998, Vol 30, Num 7, pp 549-557, issn 0010-4485Article

Dimensional measurement data analysis, Part 1 : A zone fitting algorithmCHOI, W; KURFESS, T. R.Journal of manufacturing science and engineering. 1999, Vol 121, Num 2, pp 238-245, issn 1087-1357Article

An alternate geometric perspective on MIMO systemsNAGURKA, M. L; KURFESS, T. R.Journal of dynamic systems, measurement, and control. 1993, Vol 115, Num 3, pp 538-543, issn 0022-0434Article

Foundations of classical control theory with reference of eigenvalue geometryKURFESS, T. R; NAGURKA, M. L.Journal of the Franklin Institute. 1993, Vol 330, Num 2, pp 213-227, issn 0016-0032Article

A geometric representation of root sensitivityKURFESS, T. R; NAGURKA, M. L.Journal of dynamic systems, measurement, and control. 1994, Vol 116, Num 2, pp 305-309, issn 0022-0434Article

A micromachined scanning grating interferometer for the out-of-plane vibration measurement of MEMSKIM, B; DEGERTEKIN, F. L; KURFESS, T. R et al.Journal of micromechanics and microengineering (Print). 2007, Vol 17, Num 9, pp 1888-1898, issn 0960-1317, 11 p.Article

Integration of an open architecture controller with a diamond turning machineULMER, B. C; KURFESS, T. R.Mechatronics (Oxford). 1999, Vol 9, Num 4, pp 349-361, issn 0957-4158Article

An active piezoelectric probe for precision measurement on a CMMBITTLE, S. D; KURFESS, T. R.Mechatronics (Oxford). 1997, Vol 7, Num 4, pp 337-354, issn 0957-4158Article

Use of a quality loss function to select statistical tolerancesVASSEUR, H; KURFESS, T. R; CAGAN, J et al.Journal of manufacturing science and engineering. 1997, Vol 119, Num 3, pp 410-416, issn 1087-1357Article

Decoupled control/error weighting for predictive controlKURFESS, T. R; WHITNEY, D. E.Journal of dynamic systems, measurement, and control. 1993, Vol 115, Num 1, pp 188-193, issn 0022-0434Article

Predictive control of a robotic grinding systemKURFESS, T. R; WHITNEY, D. E.Journal of engineering for industry. 1992, Vol 114, Num 4, pp 412-420, issn 0022-0817Article

Metrology of high aspect ratio MEMSNICHOLS, J. F; KURFESS, T. R.Microsystem technologies. 2004, Vol 10, Num 6-7, pp 556-559, issn 0946-7076, 4 p.Article

Adaptive pole-zero cancellation in grinding force controlJENKINS, H. E; KURFESS, T. R.IEEE transactions on control systems technology. 1999, Vol 7, Num 3, pp 363-370, issn 1063-6536Article

Sampling uncertainty in coordinate measurement data analysisWONCHEOL CHOI; KURFESS, T. R; CAGAN, J et al.Precision engineering. 1998, Vol 22, Num 3, pp 153-163, issn 0141-6359Article

Statistical verification of conformance to geometric toleranceKURFESS, T. R; BANKS, D. L.Computer-aided design. 1995, Vol 27, Num 5, pp 353-361, issn 0010-4485Article

An analysis and improvement of the predictive control integrating componentKURFESS, T. R; WHITNEY, D. E.Journal of dynamic systems, measurement, and control. 1993, Vol 115, Num 1, pp 183-188, issn 0022-0434Article

Development and control of an automated robotic weld bead grinding systemWHITNEY, D. E; EDSALL, A. C; TODTENKOPF, A. B et al.Journal of dynamic systems, measurement, and control. 1990, Vol 112, Num 2, pp 166-176, issn 0022-0434, 11 p.Article

Determination of a dynamic grinding modelJENKINS, H. E; KURFESS, T. R; LUDWICK, S. J et al.Journal of dynamic systems, measurement, and control. 1997, Vol 119, Num 2, pp 289-293, issn 0022-0434Article

Verification of a dynamic grinding modelKURFESS, T. R; WHITNEY, D. E; BROWN, M. L et al.Journal of dynamic systems, measurement, and control. 1988, Vol 110, Num 4, pp 403-409, issn 0022-0434Article

SOI-based micro scanning grating interferometers : device characterization, control and demonstration of parallel operationKARHADE, O. G; DEGERTEKIN, F. L; KURFESS, T. R et al.Journal of micromechanics and microengineering (Print). 2008, Vol 18, Num 4, issn 0960-1317, 045007.1-045007.8Article

Design of a robust controller for a grinding systemJENKINS, H. E; KURFESS, T. R; DORF, R. C et al.IEEE transactions on control systems technology. 1996, Vol 4, Num 1, pp 40-49, issn 1063-6536Article

Design and implementation of a tube wall thickness measurement systemLUDWICK, S. J; JENKINS, H. E; KURFESS, T. R et al.Journal of manufacturing science and engineering. 1998, Vol 120, Num 2, pp 471-475, issn 1087-1357Article

A multivariate statistical approach to metrologyKURFESS, T. R; BANKS, D. L; WOLFSON, L. J et al.Journal of manufacturing science and engineering. 1996, Vol 118, Num 4, pp 652-657, issn 1087-1357Article

Diagnostics and prognostics of a single surface defect on roller bearingsLI, Y; ZHANG, C; KURFESS, T. R et al.Proceedings of the Institution of Mechanical Engineers. Part C, Journal of mechanical engineering science. 2000, Vol 214, Num 9, pp 1173-1185, issn 0954-4062Article