Analysis of pipe bends with symmetrical noncircular cross sectionsWHATHAM, J. F.Journal of applied mechanics. 1987, Vol 54, Num 3, pp 604-610, issn 0021-8936Article

Fatigue cracking of splitter plates in pipe elbow = Fissuration par fatigue de lames directrices montées dans un coude de canalisationWelding in the world. 1985, Vol 23, Num 1-2, pp 20-26, issn 0043-2288Article

Schnellbestimmung der Schweissnahtlaenge an Rohrwinkelstuecken = Quick determination of weld seam length on tube bendsGUT, H.Blech, Rohre, Profile. 1984, Vol 31, Num 12, pp 565-566, issn 0006-4688Article

GRP pipe bends subjected to out-of-plane flexure with and without pressureKITCHING, R; MYLER, P; TAN, A. L et al.Journal of strain analysis for engineering design. 1988, Vol 23, Num 4, pp 187-199, issn 0309-3247Article

Stress fields for an in-plane and shear force acting on a 90° elbow or pipe bendLANG, H. A.International journal of pressure vessels and piping. 1984, Vol 16, Num 4, pp 263-284, issn 0308-0161Article

Pipe loop or expansion joint?BROYLES, R. K.Chemical engineering (New York, NY). 1985, Vol 92, Num 21, pp 103-106, issn 0009-2460Article

Photoelastic investigation of the stresses in mitred bent-cylinders under bending. II: For various bent-anglesSAWA, Y.Bulletin of the JSME. 1984, Vol 27, Num 229, pp 1339-1345, issn 0021-3764Article

Stress fields for a normal force acting on the end of a 90° elbow or pipe bendLANG, H. A.International journal of pressure vessels and piping. 1984, Vol 17, Num 3, pp 163-172, issn 0308-0161Article

Maximum stresses and flexibility factors of smooth pipe bends with tangent pipe terminations under in-plane bendingTHOMSON, G; SPENCE, J.Journal of pressure vessel technology. 1983, Vol 105, Num 4, pp 329-336, issn 0094-9930Article

Stress analyses of wrinkle bends in pipelineMURRAY, N. W.Thin-walled structures. 1993, Vol 17, Num 1, pp 65-80, issn 0263-8231Article

Increasing the design strength of piping fittingsMAKHUTOV, N. A; SERIKOV, S. V; KOTOUSOV, A. G et al.Strength of materials. 1991, Vol 23, Num 4, pp 468-472, issn 0039-2316Article

Pipe bend analysis by thin shell theoryWHATHAM, J. F.Journal of applied mechanics. 1986, Vol 53, Num 1, pp 173-180, issn 0021-8936Article

Twist-bending of a 90° elbow or pipe bendLANG, H. A.International journal of pressure vessels and piping. 1984, Vol 16, Num 1, pp 67-74, issn 0308-0161Article

In-plane bending behavior of pipe bends with end constraints under steady-state creepCHAN, K. L. C; BOYLE, J. T; SPENCE, J et al.Journal of pressure vessel technology. 1984, Vol 106, Num 4, pp 330-335, issn 0094-9930Article

Plastic hinge formation in elbows and curved tubingLANG, H. A.International journal of pressure vessels and piping. 1984, Vol 16, Num 3, pp 165-171, issn 0308-0161Article

Elementary solutions for the propagation of ovalization along straight pipes and elbowsMILLARD, A; ROCHE, R.International journal of pressure vessels and piping. 1984, Vol 16, Num 2, pp 101-129, issn 0308-0161Article

Effect of internal pressure on flexibility factors in pipe elbows with end constraintsNATARAJAN, R; MIRZA, S.Journal of pressure vessel technology. 1985, Vol 107, Num 1, pp 60-63, issn 0094-9930Article

Simulation of flow meter calibration factors for various installation effectsHOLM, M; STANG, J; DELSING, J et al.Measurement. 1995, Vol 15, Num 4, pp 235-244, issn 0263-2241Article

UNTERSUCHUNG DER WANDSCHUBSPANNUNG IN ROHRKRUEMMERN = EXPERIMENTATION SUR LA CONTRAINTE TANGENTIELLE SUR LA PAROI DE COUDES TUBULAIRESFISCHER G.1983; MASCHINENBAUTECHNIK; ISSN 0025-4495; DDR; DA. 1983; VOL. 32; NO 7; PP. 316-318; ABS. RUS/ENG; BIBL. 5 REF.Article

MODIFICATION OF THE FORM OF THE PIPE SECTION. CRITERIUM FOR GOOD OPERATION OF PIPE BENDSAKSEL'ROD MA; BOJDOVA TI; KIRSANOV YU YA et al.1982; ENERG. ELEKTRIF. (KIEV); ISSN 0424-9879; UKR; DA. 1982; NO 1; PP. 19-21; BIBL. 2 REF.Article

Hydraulic design procedure for bypass flow meters using a pipe bendYUAN, B. Z; NISHIYAMA, S; FUKADA, M et al.Transactions of the ASAE. 2003, Vol 46, Num 2, pp 279-285, issn 0001-2351, 7 p.Article

THE ROLE OF COMPUTER GRAPHICS AT THE DESIGN/PRODUCTION INTERFACE OF A COMPANY MANUFACTURING SHEET METAL COMPONENTSCONSTANTINOU S; BARKER J; RATHMILL K et al.1981; TOOLING; GBR; DA. 1981-09; VOL. 35; NO 9; PP. 3-20; BIBL. 11 REF.Article

Coudes avec poche tampon pour le transport des matériaux abrasifs = Elbow with buffer zone for abrasive materialsL' Industrie céramique & verrière (Paris). 1996, Num 918, issn 1169-873X, p. 609Article

Ein neuartiger verschleissarmer Krümmer für Rohrleitungs-Transport-Systeme = Un nouveau coude, presque exempt d'usure, destiné aux systèmes de transport par tuyauteries = A new wear-resistant pipe elbow for pipeline transportation systemsKING, H. G.Aufbereitungs-Technik. 1989, Vol 30, Num 9, pp 545-548, issn 0004-783XArticle

Creep flexibility and stress factors for pipe bends with end constraints under in-plane or out-of-plane loadingCHAN, K. L. C; BOYLE, J. T.International journal of pressure vessels and piping. 1986, Vol 23, Num 4, pp 259-293, issn 0308-0161Article