A ballistic study of micro-particle penetration to the oral mucosaMITCHELL, Thomas J; KENDALL, Mark A. F; BELLHOUSE, Brian J et al.International journal of impact engineering. 2003, Vol 28, Num 6, pp 581-599, issn 0734-743X, 19 p.Article

Low viscosity feedstocks for powder injection mouldingLAPOINTE, F; TURENNE, S; JULIEN, B et al.Powder metallurgy. 2009, Vol 52, Num 4, pp 338-344, issn 0032-5899, 7 p.Article

Deposition of multicomponent coatings by Cold SprayKLINKOV, S. V; KOSAREV, V. F; SOVA, A. A et al.Surface & coatings technology. 2008, Vol 202, Num 24, pp 5858-5862, issn 0257-8972, 5 p.Article

Influence of powder injection point position on efficiency of powder preheating in cold spray: Numerical studySOVA, A; GRIGORIEV, S; KOCHETKOVA, A et al.Surface & coatings technology. 2014, Vol 242, pp 226-231, issn 0257-8972, 6 p.Article

Influence of mixing and effect of agglomerates on the green and sintered properties of 97W―2.1Ni―O.9Fe heavy alloysSURI, Pavan; GERMAN, Randall M; DE SOUZA, Jupiter P et al.International journal of refractory metals & hard materials. 2009, Vol 27, Num 4, pp 683-687, issn 0958-0611, 5 p.Article

Mn-Zn Ferrite Round Cable EMI Suppressor With Deep Grooves and a Secondary Short Circuit for Different Frequency RangesLUKOVIC, Miloljub D; NIKOLIC, Maria V; BLAZ, Nelu V et al.IEEE transactions on magnetics. 2013, Vol 49, Num 3, pp 1172-1177, issn 0018-9464, 6 p., 2Article

Preparation and characterization of micro components fabricated by micro powder injection moldingLIU, L; LOH, N. H; TAY, B. Y et al.Materials characterization. 2011, Vol 62, Num 6, pp 615-620, issn 1044-5803, 6 p.Article

Injection de poudre de coke à travers les tuyères d'un cubilotINAGAKI, K; INOUE, T.Imono. 1985, Vol 57, Num 1, pp 9-13, issn 0021-4396Article

Study of residual gas formed during plasma debinding of powder injection moulded partsDA SILVA SOBRINHO, A. S; SPELLER, C. V; AMORIM, J et al.Journal of physics. D, Applied physics (Print). 2006, Vol 39, Num 1, pp 94-98, issn 0022-3727, 5 p.Article

Desenvolvimento de equipamento para injeção profunda de pós reativos em panela de aço = Equipement des poches d'aciérie pour l'injection profonde de poudres réactives = Steel ledle facility development for deep injection of reactive powdersGALVAO, R. C; RODRIGUES DE SOUZA, H; DE CRUDIS, L. J et al.Metalurgia ABM. 1984, Vol 40, Num 320, pp 373-379, issn 0026-0983Article

Production of micro components by micro powder injection moldingLIU, Z. Y; LOH, N. H; TOR, S. B et al.Journal of materials science letters. 2001, Vol 20, Num 4, pp 307-309, issn 0261-8028Article

KINETIC BEHAVIOR OF GAS AND POWDER DURING INJECTIONNARITA K; MAKINO T; MATSUMOTO H et al.1981; KOBE STEEL ENG. REP., RES. DEV.; JPN; DA. 1981-10; VOL. 31; NO 4; PP. 65-68; BIBL. 16 REF.Article

Influence of ball milling on powder characteristics and feedstock rheological behaviours of injection moulded ultrafine 98w―1Ni―1FeHAN, Y; FAN, J. L; LIU, T et al.Powder metallurgy. 2013, Vol 56, Num 2, pp 135-142, issn 0032-5899, 8 p.Article

Mechanical alloying of FeAl intermetallic powder for metal injection moulding processSONG, H. X; WU, Y. X; YUAN, S et al.Powder metallurgy. 2010, Vol 53, Num 3, pp 208-212, issn 0032-5899, 5 p.Article

Optimisation of process conditions in powder injection moulding of microsystem components using robust design method Part 2 - Secondary design parametersURVAL, R; LEE, S; ATRE, S. V et al.Powder metallurgy. 2010, Vol 53, Num 1, pp 71-81, issn 0032-5899, 11 p.Article

Effect of sintering parameters on mechanical properties of injection moulded Ti―6Al―₄V alloysERGÜL, E; OZKAN GÜLSOY, H; GÜNAY, V et al.Powder metallurgy. 2009, Vol 52, Num 1, pp 65-71, issn 0032-5899, 7 p.Article

SiC_p/Cu composites prepared by pressureless infiltration of copper into porous SiC preformsZHANG, L; QU, X. H; HE, X. B et al.Powder metallurgy. 2008, Vol 51, Num 1, pp 53-58, issn 0032-5899, 6 p.Article

Microstructural and mechanical properties of injection moulded gas and water atomised 17-4 PH stainless steel powderGBLSOY, H. O; OZBEK, S; BAYKARA, T et al.Powder metallurgy. 2007, Vol 50, Num 2, pp 120-126, issn 0032-5899, 7 p.Article

Statistical analysis of fibre fracture during powder injection mouldingGERMAN, Randall M; AHMAD, F.Powder metallurgy. 2006, Vol 49, Num 4, pp 307-313, issn 0032-5899, 7 p.Article

Formation of aluminium nitride during sintering of powder injection moulded aluminiumKENT, D; QIAN, M; SCHAFFER, G. B et al.Powder metallurgy. 2010, Vol 53, Num 2, pp 118-124, issn 0032-5899, 7 p.Article

Powder injection molding research at Rensselaer : an updateMESSLER, R. W.SAE transactions. 1989, Vol 98, Num 5, pp 322-331, issn 0096-736X, 10 p.Article

Powder injection moulding of metal ceramic interpenetrating phase compositesHEIN, S. B.Powder metallurgy. 2014, Vol 57, Num 5, pp 348-356, issn 0032-5899, 9 p.Article

Microstructure and mechanical properties of injection moulded Nimonic-90 superalloy partsÖZGÜN, Ö; GÜLSOY, H. O; FINDIK, F et al.Powder metallurgy. 2012, Vol 55, Num 5, pp 405-414, issn 0032-5899, 10 p.Article

Integrated filling, packing and cooling CAE analysis of powder injection moulding partsAHN, S; CHUNG, S. T; ATRE, S. V et al.Powder metallurgy. 2008, Vol 51, Num 4, pp 318-326, issn 0032-5899, 9 p.Article

Process simulation of powder injection moulding : identification of significant parameters during mould filling phaseATRE, S. V; PARK, S.-J; ZAUNER, R et al.Powder metallurgy. 2007, Vol 50, Num 1, pp 76-85, issn 0032-5899, 10 p.Article