Antibacterial property of Ce-bearing stainless steelsHEMIN JING; XINQIANG WU; YONGQIAN LIU et al.Journal of materials science. 2007, Vol 42, Num 13, pp 5118-5122, issn 0022-2461, 5 p.Article

Damage identification of full scale four-story steel building using multi-input multi-output modelsHOTHU, Hien; MITA, Akira.Proceedings of SPIE, the International Society for Optical Engineering. 2011, Vol 7981, issn 0277-786X, isbn 978-0-8194-8543-4, 79814A.1-79814A.7, 2Conference Paper

γ ↔ ε Transformation Behavior of Austenitic-Martensitic FeMn(Cr) SteelsWEISS, A; TRANTA, F; SCHELLER, P. R et al.Praktische Metallographie. 2012, Vol 49, Num 5, pp 264-277, issn 0032-678X, 14 p.Article

Multi-scale hybrid sensor nodes for acceleration-impedance monitoring for steel structural connectionsPARK, Jae-Hyung; HO, Duc-Duy; NGUYEN, Khac-Duy et al.Proceedings of SPIE, the International Society for Optical Engineering. 2011, Vol 7981, issn 0277-786X, isbn 978-0-8194-8543-4, 79810E.1-79810E.14, 2Conference Paper

Microstructure development in ridging affected ferritic stainless steelsSZTWIERTNIA, Krzysztof; POSPIECH, J. A. N; ROSTEK, Tomasz et al.Archives of metallurgy. 2002, Vol 47, Num 2, pp 197-204, issn 0860-7052Article

The ferrite/austenite ratio of duplex stainless steelsPOHL, M.Zeitschrift für Metallkunde. 1995, Vol 86, Num 2, pp 97-102, issn 0044-3093Article

Development of high strength low alloy TRIP-aided steels with annealed martensite matrixSUGIMOTO, Koh-Ichi; KIKUCHI, Ryo; HASHIMOTO, Shun-Ichi et al.Steel research. 2002, Vol 73, Num 6-7, pp 253-258, issn 0177-4832Article

Evolution of secondary phases in austenitic stainless steels during long-term exposures at 600, 650 and 800 °CVACH, Marian; KUNIKOVA, Terézia; DOMANKOVA, Maria et al.Materials characterization. 2008, Vol 59, Num 12, pp 1792-1798, issn 1044-5803, 7 p.Article

Mild steels coated with 14% manganese covered electrodes (E7-UM-200-K and El-UM-350) : Phenomena at the steel-coating interfaceMOLLEDA, F; MORA, J; MOLLEDA, F. J et al.Materials characterization. 2006, Vol 57, Num 4-5, pp 300-305, issn 1044-5803, 6 p.Article

Microstructural evaluation of C-free martensitic alloys at high temperaturesYAMADA, Katsumi; IGARASHI, Masaaki; MUNEKI, Seiichi et al.ISIJ international. 2002, Vol 42, Num 8, pp 882-888, issn 0915-1559Article

Comparison of early stages of precipitation in Mo-rich and Mo-poor maraging stainless steelsANDERSSON, M; STILLER, K; HÄTTESTRAND, M et al.Surface and interface analysis. 2007, Vol 39, Num 2-3, pp 195-200, issn 0142-2421, 6 p.Conference Paper

The morphology and formation mechanism of pearlite in steelsZHANG, M.-X; KELLY, P. M.Materials characterization. 2009, Vol 60, Num 6, pp 545-554, issn 1044-5803, 10 p.Article

In-situ observation on the growth of Widmanstätten sideplates in an Fe-C-Mn steelCHENG, L; WU, K. M; WAN, X. L et al.Materials characterization. 2014, Vol 87, pp 86-94, issn 1044-5803, 9 p.Article

Numerical Modeling of Hysteresis in Si-Fe SteelsCARDELLI, Ermanno; DELLA TORRE, Edward; FABA, Antonio et al.IEEE transactions on magnetics. 2014, Vol 50, Num 2, issn 0018-9464, 7008004.1-7008004.4Conference Paper

Structure and properties of chromium nickel dual phase nitrogen steel after solidification, plastic working and heat treatmentKAPUTKINA, L. M; PROKOSHKINA, V. G; SVYAZHIN, A. G et al.Materials science forum. 1999, pp 835-838, issn 0255-5476, isbn 0-87849-843-5Conference Paper

Creep behavior of an A286 type stainless steelDE CICCO, H; LUPPO, M. I; RAFFAELI, H et al.Materials characterization. 2005, Vol 55, Num 2, pp 97-105, issn 1044-5803, 9 p.Article

Characterization of the microstructure and transformation behaviour of strained and nonstrained austenite in Nb-V-alloyed C-Mn steelPETROV, R; KESTENS, L; HOUBAERT, Y et al.Materials characterization. 2004, Vol 53, Num 1, pp 51-61, issn 1044-5803, 11 p.Article

Alloying effects on the microstructure and phase stability of Fe-Cr-Mn steelsRAWERS, James C.Journal of materials science. 2008, Vol 43, Num 10, pp 3618-3624, issn 0022-2461, 7 p.Article

Strengthening of nitrogen-containing maraging steelsKAPUTKINA, L. M; PROKOSHKINA, V. G; ULUNTSEV, D. Yu et al.Materials science forum. 1999, pp 327-332, issn 0255-5476, isbn 0-87849-843-5Conference Paper

Exploring the relationship between ferrite fraction and morphology and the electromagnetic properties of steelYIN, W; PEYTON, A. J; STRANGWOOD, M et al.Journal of materials science. 2007, Vol 42, Num 16, pp 6854-6861, issn 0022-2461, 8 p.Article

A computational approach to evaluate temperature and heat partition in machining with multilayer coated toolsGRZESIK, W; NIESLONY, P.International journal of machine tools & manufacture. 2003, Vol 43, Num 13, pp 1311-1317, issn 0890-6955, 7 p.Article

EFFECT OF RADIOGENIC HELIUM ON STAINLESS STEEL 12Cr18Ni10Ti STRUCTURAL CHANGES AND HYDROGEN SORPTIONDENISOV, E; KANASHENKO, S; CAUSEY, R et al.Fusion science and technology. 2008, Vol 54, Num 2, pp 493-496, 4 p.Conference Paper

Study of welding characteristics of 0.3C-CrMoV(ESR) ultrahigh strength steelSURESH, M. R; SINHA, P. P; SARMA, D. S et al.Journal of materials science. 2007, Vol 42, Num 14, pp 5602-5612, issn 0022-2461, 11 p.Article

Comparison of corrosion properties of passive films formed on phase reversion induced nano/ultrafine-grained 321 stainless steelLV JINLONG; LUO HONGYUN.Applied surface science. 2013, Vol 280, pp 124-131, issn 0169-4332, 8 p.Article

Low-pressure ion nitriding of AISI 304 austenitic stainless steel with an intensified glow dischargeMELETIS, E. I; YAN, S.Journal of vacuum science and technology. A. Vacuum, surfaces, and films. 1993, Vol 11, Num 1, pp 25-33, issn 0734-2101Article