Comparative Studies on Enhanced Interfacial Adhesion between PE and PA6 through Two Routes in a Sequential Injection Molding ProcessGENJIE JIANG; FENGSHUN ZHANG; HONG WU et al.Polymer-plastics technology and engineering (Softcover ed). 2014, Vol 53, Num 1-3, pp 9-18, issn 0360-2559, 10 p.Article

Investigation on the Morphology and Tensile Behavior of β-Nucleated Isotactic Polypropylene with Different Stereo-Defect DistributionHONGMEI PENG; BIN WANG; JINGGANG GAI et al.Journal of applied polymer science (Print). 2014, Vol 131, Num 6, issn 0021-8995, 40027.1-40027.10Article

Measurement of the visual perceptibility of sink marks on injection molding parts by a new fast processing modelGRUBER, Dieter P; MACHER, Johannes; HABA, Dietmar et al.Polymer testing. 2014, Vol 33, pp 7-12, issn 0142-9418, 6 p.Article

Mechanical and Thermal Analysis of Injection Molded Poly(methyl methacrylate) Modified with 9,10-Dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) Fire RetarderKRALA, Grzegorz; UBOWSKA, Agnieszka; KOWALCZYK, Krzysztof et al.Polymer engineering and science. 2014, Vol 54, Num 5, pp 1030-1037, issn 0032-3888, 8 p.Article

Potential of Conformal Cooling Channels in Rapid Heat Cycle Molding: A ReviewSHAYFULL, Z; SHARIF, S; AZLAN MOHD. ZAIN et al.Advances in polymer technology. 2014, Vol 33, Num 1, issn 0730-6679, 21381.1-21381.24Article

Process―Property―Structure Relationship in Miniaturized Injection Moulded Polyoxymethylene SamplesBALDI, F; BONGIORNO, A; FASSI, I et al.Polymer engineering and science. 2014, Vol 54, Num 3, pp 512-521, issn 0032-3888, 10 p.Article

Tailoring the Crystalline Morphologies and Mechanical Properties of High-Density Polyethylene Parts by a Change in the Fluid Flow Pattern Under Gas-Assisted Injection MoldingQUANPING ZHANG; LONG WANG; XIAOCHAO XIA et al.Journal of applied polymer science (Print). 2014, Vol 131, Num 11, issn 0021-8995, 40349.1-40349.10Article

Temperature dependency comparison of ultrasonic wave propagation between injected and sintered thermoplasticsTRANNOY, Guillaume; NIKOLOVSKI, Jean-Pierre; HOLE, Stéphane et al.Polymer testing. 2014, Vol 35, pp 34-44, issn 0142-9418, 11 p.Article

Largely enhanced molecular orientation and mechanical property of injection-molded high-density polyethylene parts via the synergistic effect of polyamide 6 in situ microfibrillar and intense shear flowJIAN FENG; ZHANG, Rui-Yan; WU, Jing-Jing et al.Colloid and polymer science (Print). 2014, Vol 292, Num 11, pp 3033-3044, issn 0303-402X, 12 p.Article

Super Toughened Poly(L-lactide)/Thermoplastic Polyurethane Blends Achieved by Adding Dicumyl PeroxideSHI, Yun-Yun; DU, Xue-Chong; YANG, Jing-Hui et al.Polymer-plastics technology and engineering (Softcover ed). 2014, Vol 53, Num 11-14, pp 1344-1353, issn 0360-2559, 10 p.Article

Morphology and mechanical behavior of isotactic polypropylene with different stereo-defect distribution in injection moldingHONGMEI PENG; BIN WANG; JINGGANG GAI et al.Polymers for advanced technologies. 2014, Vol 25, Num 12, pp 1464-1470, issn 1042-7147, 7 p.Conference Paper

Effects of insert film on asymmetric mold temperature and associated part warpage during in-mold decoration injection molding of PP partsCHEN, Hui-Li; CHEN, Shia-Chung; LIAO, Won-Hsion et al.International communications in heat and mass transfer. 2013, Vol 41, pp 34-40, issn 0735-1933, 7 p.Article

Pressurized Water Pellets and Supercritical Nitrogen in Injection MoldingDUARTE CABRERA, Eusebio; MULYANA, Rachmat; CASTRO, Jose M et al.Journal of applied polymer science. 2013, Vol 127, Num 5, pp 3760-3767, issn 0021-8995, 8 p.Article

Unusual hierarchical structures of mini-injection molded isotactic polypropylene/ultrahigh molecular weight polyethylene blendsYUAN AN; BAO, Rui-Ying; LIU, Zheng-Ying et al.European polymer journal. 2013, Vol 49, Num 2, pp 538-548, issn 0014-3057, 11 p.Article

Back melt flow in injection―compression molding: Effect on part thickness distributionGUAN, Wei-Sheng; HUANG, Han-Xiong.International communications in heat and mass transfer. 2012, Vol 39, Num 6, pp 792-797, issn 0735-1933, 6 p.Article

Investigation the effects of obstacle geometries and injection molding parameters on weld line strength using experimental and finite element methods in plastic injection moldingOZCELIK, Babur; KURAM, Emel; MUSTAFA TOPAL, M et al.International communications in heat and mass transfer. 2012, Vol 39, Num 2, pp 275-281, issn 0735-1933, 7 p.Article

Morphological Distribution in Micro-Injected Polypropylene Parts in the Presence of β-Nucleating AgentHONG LIU; LEI ZHANG; FANGHUI LIU et al.Journal of macromolecular science. Physics. 2012, Vol 51, Num 7-9, pp 1566-1582, issn 0022-2348, 17 p.Article

Morphologies and Mechanical Properties of High-Density Polyethylene Induced by the Addition of Small Amounts of Both Low-and High-Molecular-Weight Polyolefin under Shear Stress Applied by Dynamic Packing Injection MoldingJIANGUO CAO; XUEQIN GAO; KAIZHI SHEN et al.Journal of macromolecular science. Physics. 2012, Vol 51, Num 10-12, pp 2519-2526, issn 0022-2348, 8 p.Article

Prediction of warpage in plastic injection molding based on design of experimentsWEI GUO; LIN HUA; HUAJIE MAO et al.Journal of mechanical science and technology. 2012, Vol 26, Num 4, pp 1133-1139, issn 1738-494X, 7 p.Article

Alternating Multilayer Structure of Polyethylene/ Polypropylene Blends Obtained Through Injection MoldingKUN JIANG; FEILONG YU; HONGWEI BAI et al.Journal of applied polymer science. 2012, Vol 124, Num 6, pp 4452-4456, issn 0021-8995, 5 p.Article

Effects of compatibilizers on mechanical and antibacterial properties of injection molded nano-ZnO filled polypropyleneALTAN, Mirigul; YILDIRIM, Huseyin.Journal of composite materials. 2012, Vol 46, Num 25, pp 3189-3199, issn 0021-9983, 11 p.Article

Formation Mechanism of Crystal Morphologies in LLDPE/HDPE Blends Investigated via Water-Assisted and Conventional Injection MoldingBIN WANG; HUANG, Han-Xiong.Polymer engineering and science. 2012, Vol 52, Num 1, pp 117-124, issn 0032-3888, 8 p.Article

Surface wear of TiN coated nickel tool during the injection moulding of polymer micro Fresnel lensesTOSELLO, Guido; NØRGAARD HANSEN, Hans; GASPARIN, Stefania et al.CIRP annals. 2012, Vol 61, Num 1, pp 535-538, issn 0007-8506, 4 p.Conference Paper

A SNCCDBAGG-Based NN Ensemble Approach for Quality Prediction in Injection Molding ProcessYANG LIU; WANG, Fu-Li; CHANG, Yu-Qing et al.IEEE transactions on automation science and engineering. 2011, Vol 8, Num 2, pp 424-427, issn 1545-5955, 4 p.Article

Cavity Air Flow Behavior During Filling in Microinjection MoldingGRIFFITHS, C. A; DIMOV, S. S; SCHOLZ, S et al.Journal of manufacturing science and engineering. 2011, Vol 133, Num 1, issn 1087-1357, 011006.1-011006.10Article