A study of localized shrinkage in injection molding with high thermal conductivity moldsIYER, Natraj; RAMANI, Karthik.The Journal of injection molding technology. 2002, Vol 6, Num 2, pp 73-90, issn 1533-905XArticle

Experimental measurements and simulation of particle migration in pressure-driven tube flow: Applications to flow in runnersLAM, Y. C; CHEN, X; TAN, K. W et al.The Journal of injection molding technology. 2002, Vol 6, Num 1, pp 45-57, issn 1533-905XArticle

Injection molding high aspect ratio microfeaturesDONGGANG YAO; BYUNG KIM.The Journal of injection molding technology. 2002, Vol 6, Num 1, pp 11-17, issn 1533-905XArticle

Polymer melt manipulation and in-process morphology control during molding processes: A reviewKIKUCHI, Akihisa; COULTER, John P; ANGSTADT, David C et al.The Journal of injection molding technology. 2002, Vol 6, Num 2, pp 91-106, issn 1533-905XArticle

Understanding of a new paradigm in high modulus nylon 6 grades for load bearing and lightweight applicationsKAGAN, Val A.The Journal of injection molding technology. 2002, Vol 6, Num 1, pp 18-36, issn 1533-905XArticle

Injection molding of polypropylene reinforced with thermotropic liquid crystalline polymer microfibrils. Part III: Combination of glass and TLCPHUANG, J; BAIRD, D. G.The Journal of injection molding technology. 2002, Vol 6, Num 3, pp 187-193, issn 1533-905X, 7 p.Article

Three-dimensional filling and post-filling simulation of metal injection moldingILINCA, Florin; HETU, Jean-Francois; DERDOURI, Abdessalem et al.The Journal of injection molding technology. 2002, Vol 6, Num 4, pp 229-238, issn 1533-905X, 10 p.Article

Three-dimensional simulation of reactive polymeric flow during microchip encapsulationHAN, Ruihua; GUPTA, Mahesh; CROUTHAMEL, David L et al.The Journal of injection molding technology. 2002, Vol 6, Num 3, pp 203-219, issn 1533-905X, 17 p.Article

Reliability of mold filling simulation for part designREIFSCHNEIDER, Louis G.The Journal of injection molding technology. 2001, Vol 5, Num 1, pp 38-48, issn 1533-905XArticle

Correlation between morphology distribution of injection molded polypropylene and processing history identified by numerical simulationLIU, G; EDWARD, G.The Journal of injection molding technology. 2001, Vol 5, Num 3, pp 133-140, issn 1533-905XArticle

Documenting and simulating flow segregation in geometrically balanced runnersREIFSCHNEIDER, Louis G.The Journal of injection molding technology. 2001, Vol 5, Num 4, pp 208-223, issn 1533-905XArticle

Injection molding of a robust composite system based on polypropylene reinforced with thermotropic liquid crystalline polymer microfibrilsBAIRD, D. G; HUANG, W; HUANG, J et al.The Journal of injection molding technology. 2001, Vol 5, Num 4, pp 233-245, issn 1533-905XArticle

Microcellular foam processing in reciprocating-screw injection molding machinesJINGYI XU; PIERICK, David.The Journal of injection molding technology. 2001, Vol 5, Num 3, pp 152-159, issn 1533-905XArticle

Process and tooling factors affecting sink marks for amorphous and crystalline resinsTURSI, Dan; BISTANY, S. P.The Journal of injection molding technology. 2000, Vol 4, Num 3, pp 114-119, issn 1533-905XArticle

Structure/process/part quality relationship for BMC injection moldingMENIO, Stéphane; LAFRANCHE, Eric; PABIOT, José et al.The Journal of injection molding technology. 2000, Vol 4, Num 3, pp 107-113, issn 1533-905XArticle

Effect of thermal dissymmetries on the morphology and internal stresses of injection-molded polypropylene parts : Influence on deformationLAFRANCHE, E; PABIOT, J.The Journal of injection molding technology. 2000, Vol 4, Num 2, pp 51-64, issn 1533-905XArticle

Joining of nylon based plastic components : Benefits of vibration and hot plate welding technologiesKAGAN, V. A.The Journal of injection molding technology. 2000, Vol 4, Num 1, pp 8-21, issn 1533-905XArticle

In-plane deformation analysis of plastic parts in the injection molding processLEE, H.-S.The Journal of injection molding technology. 1999, Vol 3, Num 1, pp 11-20, issn 1533-905XArticle

Generalization of a method using neural networks to predict part quality control during injection moldingHELPS, C. R; STRONG, A. B; AL-ZUBI, R et al.The Journal of injection molding technology. 1999, Vol 3, Num 4, pp 212-225, issn 1533-905XArticle

Color and gloss-the connection to process conditionsDAWKINS, E; ENGELMANN, P; HORTON, K et al.The Journal of injection molding technology. 1998, Vol 2, Num 1, pp 1-7, issn 1533-905XArticle

Automatic tuning of injection molding by the Virtual Search MethodIVESTER, R; DANAI, K; KAZMER, D et al.The Journal of injection molding technology. 1998, Vol 2, Num 3, pp 103-108, issn 1533-905XArticle

Effects of Electrical Discharge Machining on the surface characteristics of mold materialsMILLER, P; GUHA, A.The Journal of injection molding technology. 1998, Vol 2, Num 3, pp 128-135, issn 1533-905XArticle

An improved mold pin gate and its flow pattern in the cavityWENLI DAI; PENGSHENG LIU; XIAYU WANG et al.The Journal of injection molding technology. 2002, Vol 6, Num 2, pp 115-119, issn 1533-905XArticle

Self-learning control for injection molding based on neural networks optimizationLIANG, Jui-Ming; WANG, Pei-Jen.The Journal of injection molding technology. 2002, Vol 6, Num 1, pp 58-71, issn 1533-905XArticle

Design Sensitivity Analysis for gas-assisted injection moldingILINCA, Florin; HETU, Jean-Francois.The Journal of injection molding technology. 2002, Vol 6, Num 3, pp 194-202, issn 1533-905X, 9 p.Article