Characterization of the interphase in glass sphere reinforced polymersAL-OSTAZ, Ahmed; AL-MOUSSAWI, Hassan; DRZAL, Lawrence T et al.Composites. Part B, Engineering. 2004, Vol 35, Num 5, pp 393-412, issn 1359-8368, 20 p.Article

Compressive strength after impact of CFRP-foam core sandwich panels in marine applicationsBULL, Peter H; EDGREN, Fredrik.Composites. Part B, Engineering. 2004, Vol 35, Num 6-8, pp 535-541, issn 1359-8368, 7 p.Article

Collapse of clamped and simply supported composite sandwich beams in three-point bendingTAGARIELLI, V. L; FLECK, N. A; DESHPANDE, V. S et al.Composites. Part B, Engineering. 2004, Vol 35, Num 6-8, pp 523-534, issn 1359-8368, 12 p.Article

High-speed synchrotron X-ray phase contrast imaging for analysis of low-Z composite microstructureYEAGER, J. D; LUO, S. N; JENSEN, Bj et al.Composites. Part A, Applied science and manufacturing. 2012, Vol 43, Num 6, pp 885-892, issn 1359-835X, 8 p.Article

Electron microprobe imaging for the characterization of polymer matrix compositesHERZOG, Benjamin; GOODELL, Barry; LOPEZ-ANIDO, Roberto et al.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 9, pp 1075-1080, issn 1359-835X, 6 p.Article

Edge machining effects on the failure of polymer matrix composite couponsGHIDOSSI, Patrick; EL MANSORI, Mohamed; PIERRON, Fabrice et al.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 7-8, pp 989-999, issn 1359-835X, 11 p.Conference Paper

Numerical simulation of hypervelocity impacts of a projectile on laminated composite plate targets by means of improved SPH methodSHINTATE, K; SEKINE, H.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 6, pp 683-692, issn 1359-835X, 10 p.Article

Influence of processing methods on the tensile and flexure properties of high temperature compositesRAMULU, M; STICKLER, P. B; MCDEVITT, N. S et al.Composites science and technology. 2004, Vol 64, Num 12, pp 1763-1772, issn 0266-3538, 10 p.Article

Influence of process induced defects on the failure of composite T-joint specimensTRASK, R. S; HALLETT, S. R; HELENON, F. M. M et al.Composites. Part A, Applied science and manufacturing. 2012, Vol 43, Num 4, pp 748-757, issn 1359-835X, 10 p.Article

Mechanical behaviour of polymer-modified ferrocement under different exposure conditions: An experimental studyRAMLI, Mahyuddin; AMIN AKHAVAN TABASSI.Composites. Part B, Engineering. 2012, Vol 43, Num 2, pp 447-456, issn 1359-8368, 10 p.Article

Effect of the defect concentration on the impact fatigue endurance of untreated and alkali treated jute-vinylester composites under normal and liquid nitrogen atmosphereSARKAR, B. K; RAY, Dipa.Composites science and technology. 2004, Vol 64, Num 13-14, pp 2213-2219, issn 0266-3538, 7 p.Article

Dependence of fracture toughness of composite laminates on interface ply orientations and delamination growth directionANDERSONS, J; KÖNIG, M.Composites science and technology. 2004, Vol 64, Num 13-14, pp 2139-2152, issn 0266-3538, 14 p.Article

Shock propagation in a tape wrapped carbon fibre compositeWOOD, D. C; APPLEBY-THOMAS, G. J; HAZELL, P. J et al.Composites. Part A, Applied science and manufacturing. 2012, Vol 43, Num 9, pp 1555-1560, issn 1359-835X, 6 p.Article

RC square sections confined by FRP: Analytical prediction of peak strengthNISTICO, Nicola; MONTI, Giorgio.Composites. Part B, Engineering. 2013, Vol 45, Num 1, pp 127-137, issn 1359-8368, 11 p.Article

The simulation of bone healing process of fractured tibia applied with composite bone plates according to the diaphyseal oblique angle and plate modulusSON, Dae-Sung; CHANG, Seung-Hwan.Composites. Part B, Engineering. 2013, Vol 45, Num 1, pp 1325-1335, issn 1359-8368, 11 p.Article

Mechanical characterization of lightweight polymer mortar modified with cork granulatesNOVOA, P. J. R. O; RIBEIRO, M. C. S; FERREIRA, A. J. M et al.Composites science and technology. 2004, Vol 64, Num 13-14, pp 2197-2205, issn 0266-3538, 9 p.Article

Limit analysis of FRP strengthened masonry arches via nonlinear and linear programmingCAPORALE, A; FEO, L; LUCIANO, R et al.Composites. Part B, Engineering. 2012, Vol 43, Num 2, pp 439-446, issn 1359-8368, 8 p.Article

A criterion for modelling initiation and propagation of matrix cracking and delamination in cross-ply laminatesREBIERE, J.-L; GAMBY, D.Composites science and technology. 2004, Vol 64, Num 13-14, pp 2239-2250, issn 0266-3538, 12 p.Article

Fatigue crack growth behavior of silica particulate reinforced epoxy resin compositeBOONYAPOOKANA, Alisa; NAGATA, Kohsoku; MUTOH, Yoshiharu et al.Composites science and technology. 2011, Vol 71, Num 8, pp 1124-1131, issn 0266-3538, 8 p.Article

Fabrication, characterization and evaluation of the mechanical properties of poly (ε-caprolactone)/nano-fluoridated hydroxyapatite scaffold for bone tissue engineeringJOHARI, N; FATHI, M. H; GOLOZAR, M. A et al.Composites. Part B, Engineering. 2012, Vol 43, Num 3, pp 1671-1675, issn 1359-8368, 5 p.Article

Development of electromagnetic shielding materials from the conductive blends of polyaniline and polyaniline-clay nanocomposite-EVA : Preparation and propertiesSUDHA, J. D; SIVAKALA, S; PRASANTH, R et al.Composites science and technology. 2009, Vol 69, Num 3-4, pp 358-364, issn 0266-3538, 7 p.Article

A micromechanical study on the effect of intra-ply properties on transverse shear fracture in fibre reinforced compositesVAUGHAN, T. J; MCCARTHY, C. T.Composites. Part A, Applied science and manufacturing. 2011, Vol 42, Num 9, pp 1217-1228, issn 1359-835X, 12 p.Article

Toughened wheat gluten and treated coconut fiber compositeCHENG DIAO; DOWDING, Timothy; HEMSRI, Sudsiri et al.Composites. Part A, Applied science and manufacturing. 2014, Vol 58, pp 90-97, issn 1359-835X, 8 p.Article

Accelerated ageing behaviors of aluminum plate with composite patches under salt fog effectWEN, S. W; XIAO, J. Y; WANG, Y. R et al.Composites. Part B, Engineering. 2013, Vol 44, Num 1, pp 266-273, issn 1359-8368, 8 p.Article

Assessment of design procedures for the use of externally bonded FRP composites in shear strengthening of reinforced concrete beamsPELLEGRINO, Carlo; VASIC, Mira.Composites. Part B, Engineering. 2013, Vol 45, Num 1, pp 727-741, issn 1359-8368, 15 p.Article