Transformation diagrams of aluminum alloys of the Al-Cu-Mg, Al-Mg-Si-Cu, and Al-Mg-Li systemsBER, L. B; KAPUTKIN, E. Ya.Physics of metals and metallography. 2001, Vol 92, Num 2, pp 199-209, issn 0031-918XArticle

KAVITATIONSKORROSION AN EINER ALUMINIUMLEGIERUNG = CORROSION PAR CAVITATION DANS UN ALLIAGE D'ALUMINIUMHIRTH FW; SPECKHARDT H.1976; WERKST. U. KORROS.; DTSCH.; DA. 1976; VOL. 27; NO 3; PP. 154-157; ABS. ANGL. FR.; BIBL. 2 REF.Article

PIECES COULEES SOUS PRESSION EN ZAMAK: UNE MEILLEURE QUALITE A UN PLUS BAS PRIX = ZINC DIE CASTINGS: BETTER QUALITY AT LOWER COST1982; ZINC INFORMATION. FONDERIE; ISSN 0373-1413; FRA; DA. 1982; NO 44; PP. 2-11; IDEM ENG GER ITAArticle

About the fracture toughness of cast alloys of the system Al-Mg-Zn-CuBELOV, N.A; EVSEEV, Yu.V; ZOLOTOREVSKIJ, V.S et al.Izvestiâ Akademii nauk SSSR. Metally. 1984, Vol 1984, Num 1, pp 120-123, issn 0568-5303Article

A metallurgical study of aluminium alloys used as aircraft componentsNAKAZATO, R. Z; CODARO, E. N; HOROVISTIZ, A. L et al.Praktische Metallographie. 2001, Vol 38, Num 2, pp 74-87, issn 0032-678XArticle

Effect of composition and processing route on the wear behaviour of Al-Si alloysLASA, L; RODRIGUEZ-IBABE, J. M.Scripta materialia. 2002, Vol 46, Num 6, pp 477-481, issn 1359-6462Article

Quantitative TEM study of the precipitation microstructure in aluminium alloy Al(MgSiCu) 6056 T6DELMAS, F; CASANOVE, M. J; LOURS, P et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2004, Vol 373, Num 1-2, pp 80-89, issn 0921-5093, 10 p.Article

The effect of rolling schedule on the behavior of Guinier-Preston zones in Al―Mg―Si―Cu alloys under thermomechanical treatmentMARKOVICH, D; GUSKOVICH, D; NESTOROVICH, S et al.Physics of metals and metallography. 1992, Vol 74, Num 4, pp 378-380, issn 0031-918XArticle

THERMAL ANALYSIS OF Al-Cu-Mg-Si ALLOY WITH Ag/Zr ADDITIONSBASSANI, Paola; GARIBOLDI, E; RIPAMONTI, D et al.Journal of thermal analysis and calorimetry. 2008, Vol 91, Num 1, pp 29-35, issn 1388-6150, 7 p.Conference Paper

Thermal conductivity of aluminium-silicon-based alloysJAROMA-WEILAND, G; REIPERT, P; BRANDT, R et al.High Temperatures. High Pressures (Print). 1998, Vol 30, Num 6, pp 671-675, issn 0018-1544Conference Paper

Verschraubung von Magnesiumkomponenten = screw connection of magnesium componentsWESTPHAL, K.Metall (Berlin, West). 2002, Vol 56, Num 1-2, pp 32-34, issn 0026-0746Article

Particle-stimulated nucleation of recrystallization for grain-size control and superplasticity in an Al-Mg-Si-Cu alloyTROEGER, L. P; STARKE, E. A.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2000, Vol 293, Num 1-2, pp 19-29, issn 0921-5093Article

Prediction of solidification behavior in AC8C alloy by thermodynamic calculationOHSASA, Kenichi; SHOJI, Mayumi; NARITA, Toshio et al.Chuzo kogaku. 2000, Vol 72, Num 8, pp 525-529, issn 1342-0429Article

Einfluss der Legierungszusammensetzung und der Homogenisierungsbedingungen auf Gefüge und Eigenschaften aushärtbarer AlMgSi1Cu-Legierungen = The effect of alloy composition and homogenization conditions on the structure and properties of heat treatable AlMgSi1Cu-alloysGÄRTNER, S; ADAM, D; HOLZE, J et al.Praktische Metallographie. 1999, Vol 36, Num 7, pp 346-366, issn 0032-678XArticle

Precipitation kinetics of AA4032 and AA6082 : A comparison based on DSC and TEMBIROLI, G; CAGLIOTI, G; MARTINI, L et al.Scripta materialia. 1998, Vol 39, Num 2, pp 197-203, issn 1359-6462Article

Quantification of overaging hardening kinetics of aluminum alloysSHA, W; LONG, A. E.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2004, Vol 35, Num 7, pp 2172-2174, issn 1073-5623, 3 p.Article

Coprecipitation of Ω and σ phases in Al-Cu-Mg-Mn alloys containing Ag and SiMUKHOPADHYAY, A. K.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2002, Vol 33, Num 12, pp 3635-3648, issn 1073-5623, 14 p.Article

Qualitative and quantitative characterization of aluminium alloys after corrosion testing = Qualitative und quantitative Charakterisierung von Aluminiumlegierungen nach der KorrosionsprüfungNAKAZATO, R. Z; CODARO, E. N; RIBEIRO, L. M. F et al.Praktische Metallographie. 2001, Vol 38, Num 6, pp 301-313, issn 0032-678XArticle

Fatigue crack growth from plain and cold expanded holes in aluminium alloysLACARAC, V; SMITH, D. J; PAVIER, M. J et al.International journal of fatigue. 2000, Vol 22, Num 3, pp 189-203, issn 0142-1123Article

Susceptibility to pitting corrosion of 6056 aluminium alloyBLANC, C; MANKOWSKI, G.Corrosion science. 1997, Vol 39, Num 5, pp 949-959, issn 0010-938XArticle

Tribological properties of Al-Si-Cu-Mg alloy-based composite-dispersing diamond nanoclusterHANADA, K; NAKAYAMA, N; MAYUZUMI, M et al.Diamond and related materials. 2002, Vol 11, Num 3-6, pp 749-752, issn 0925-9635Conference Paper

Structure and mechanical properties of hypereutectic Al-Si alloy produced by thixocasting processIWASAWA, Shigeru; SAIKAWA, Seiji; TOMITA, Taketoshi et al.Chuzo kogaku. 2001, Vol 73, Num 6, pp 373-379, issn 1342-0429Article

Microstructure and mechanical properties of spray-deposited Al-17Si-4.5Cu-O.6Mg wrought alloyYUE WU; CASSADA, W. A; LAVERNIA, E. J et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 1995, Vol 26, Num 5, pp 1235-1247, issn 1073-5623Article

Study of the thermomechanical treatment process and properties of aluminium alloy LD2ZHANG HONGZHE; ZHANG YUJIE; ZHANG XUEJUN et al.Journal of materials science letters. 1993, Vol 12, Num 20, pp 1612-1615, issn 0261-8028Article

Effect of tool rotation speed on the microstructure of the friction stir weld of an Al-Cu-Mg-Si alloyTANAKA, Sunao; KUMAGAI, Masaki; YOSHIDA, Hideo et al.Keikinzoku. 2005, Vol 55, Num 2, pp 63-67, issn 0451-5994, 5 p.Article