ON CONSTANT MEMBRANE STRESS TEST FOR SUPERPLASTIC METALS = A PROPOS DE L'ESSAI D'EMBOUTISSAGE SOUS CHARGE CONSTANTE DES METAUX SUPERPLASTIQUESGHOSH AK; HAMILTON CH.1980; METALL. TRANS. A; ISSN 0360-2133; USA; DA. 1980; VOL. 11; NO 11; PP. 1915-1918; BIBL. 8 REF.Article

WPLYW CHROPOWATOSCI POWIERZCHNI I SMARU TECHNOLOGICZNEGO NA PODATNOSC TASM STALOWYCH NISKOWEGLOWYCH DO GLABOKIEGO TLOCZENIA = EFFECT OF ROUGHNESS AND OF LUBRICANTS ON DEEP-DRAWING PROPERTIES OF LOW CARBON STEEL SHEET = INFLUENCE DE LA RUGOSITE ET DES LUBRIFIANTS SUR L'EMBOUTISSABILITE D'UN ACIER A BAS CARBONEGOLA W; GORECKI W.1979; HUTNIK; ISSN 0018-8077; POL; DA. 1979; VOL. 46; NO 12; PP. 494-500; ABS. RUS/ENG; BIBL. 11 REF.Article

DEEP-DRAWING AND IRONING OF STEEL SHEET = EMBOUTISSAGE ET ETIRAGE DE TOLES D'ACIERKHADEMY ZADEH H; COUPLAND HT; MELLOR PB et al.1980; MEM. SCI. REV. METALL.; ISSN 0025-9128; FRA; DA. 1980; VOL. 77; NO 3; PP. 363-371; BIBL. 4 REF.Article

FACTORS INFLUENCING THE FORMING LIMITS OF SHEET METALS = PARAMETRES AGISSANT SUR LES LIMITES DE FORMAGE DES TOLES METALLIQUESKLEEMOLA H; KUMPULAINEN J; RANTA ESKOLA A et al.1980; MEM. SCI. REV. METALL.; ISSN 0025-9128; FRA; DA. 1980; VOL. 77; NO 3; PP. 403-412; BIBL. 21 REF.Article

EVALUATION OF A NEW, DUAL PHARE, COLD ROLLED STEEL: FORMABILITY = EVALUATION D'UN NOUVEL ACIER DUPLEX LAMINE A FROID: FORMABILITE A FROIDBRAZIER WG; STEVENSON R.1978; S.A.E. TRANS.; USA; DA. 1978 PUBL. 1979; VOL. 87; SECT. 1; PP. 544-551; BIBL. 7 REF.Article

ERMITTLUNG DER ZIPFELGROESSE, NUTZBAREN TEILEHOEHE UND DES RONDENDURCHMESSERS IN ABHAENGIGKEIT VON DER WERKSTOFFANISOTROPIE = DETERMINATION OF EARING, WORKPIECE HEIGHT AND BLANK DIAMETER IN DEPENDENCE ON MATERIAL ANISOTROPYANSCHUETZ RW.1980; UMFORMTECHNIK; DDR; DA. 1980-10; VOL. 14; NO 5; PP. 21-29; BIBL. 9 REF.Article

ZIEHWERKZEUGE ZUM NIEDERHALTERLOSEN TIEFZIEHEN VON GROBBLECH = DRAWING DIES FOR THE DEEP-DRAWING OF PLATES WITHOUT BLANK-HOLDERKUEBERT M.1980; IND.-ANZ.; DEU; DA. 1980-08-05; VOL. 102; NO 66; PP. 36-37; BIBL. 5 REF.Article

EN 10 ANS COMMENT A EVOLUE LA NOTION DE FORMABILITE. = 10 YEARS OF DEVELOPMENT OF THE CONCEPT OF FORMABILITYDAVID GL.1979; METAUX DEFORM.; FRA; DA. 1979; NO 57; PP. 45-46Article

EFFECT OF DEEP DRAWING AND SUBSEQUENT AGING CONDITION ON DELAYED CRACKING OF STAINLESS STEELNOHARA K; WATANABE K; ONO Y et al.1982; TETSU TO HAGANE; JPN; DA. 1982-04; VOL. 68; NO 6; PP. 649-657; BIBL. 19 REF.Article

FORMING LIMIT OF 1050 ALUMINIUM ALLOY SHEETSKOHARA S; KATSUTA M; AOKI KI et al.1981; KEIKINZOKU; ISSN 0451-5994; JPN; DA. 1981; VOL. 31; NO 2; PP. 90-96; ABS. ENG; BIBL. 20 REF.Article

SELECTION OF MOLYBDENUM SHEET FOR DEEP DRAWING APPLICATIONS = AUSWAHL DES MOLYBDAENBLECHES FUER TIEFZIEHANWENDUNGEN = CHOIX DE TOLES DE MOLYBDENE POUR EMBOUTISSAGE PROFONDSALT PJ.1982; INT. J. REFRACT. HARD MET.; USA; DA. 1982-06; VOL. 1; NO 2; PP. 61-65; BIBL. 2 REF.Article

FORMING OF THIN HOT ROLLED STEEL SHEETS = EMBOUTISSAGE DE TOLES MINCES EN ACIER LAMINEES A CHAUDCRAMAY J.1980; METALL. REP. CRM; ISSN 0026-0851; BEL; DA. 1980; NO 57; PP. 9-14; ABS. GER/FRE/FLE; BIBL. 4 REF.Article

DAS FLUIDFORM-TIEFZIEHVERFAHREN, EINE WIRTSCHAFTLICHE METHODE IN DER BLECHUMFORMUNG = FLUIDFORM DEEP DRAWING - AN ECONOMICAL PROCESS IN SHEET METAL FORMING = LE PROCEDE D'EMBOUTISSAGE PROFOND SUR UN OUTIL ELASTIQUE: UNE METHODE ECONOMIQUE POUR LE FORMAGE DES TOLESMINDRUP W.1982; BLECH, ROHRE, PROFILE; DEU; DA. 1982-10; VOL. 29; NO 10; PP. 431-435; BIBL. 8 REF.Article

EFFECTS OF STRAIN PATH AND SHEET THICKNESS ON FORMING LIMIT CURVES OF 1050 ALUMINIUM SHEETSKOHARA S; KATSUTA M; AOKI K et al.1981; KEIKINZOKU; ISSN 0451-5994; JPN; DA. 1981; VOL. 31; NO 9; PP. 602-607; ABS. ENG; BIBL. 12 REF.Article

TESTING ADHERENCE OF COATINGS USING LIMITED DOME HEIGHT METHOD = ESSAI DE L'ADHERENCE DES REVETEMENTS PAR LA METHODE DE PROFONDEUR D'EMBOUTISSAGE LIMITEEMERTENS A; RENARD L; SACRE JM et al.1980; MEM. SCI. REV. METALL.; ISSN 0025-9128; FRA; DA. 1980; VOL. 77; NO 4; PP. 579-584Article

ON THE STRESS STATE DEPENDENCE OF THE STRAIN-HARDENING OF ANISOTROPIC SHEET STEEL = INFLUENCE DE L'ETAT DES CONTRAINTES SUR LE DURCISSEMENT PAR DEFORMATION DE TOLES D'ACIER ANISOTROPESRANTA ESKOLA AJ.1979; METALL. TRANS. A; ISSN 0360-2133; USA; DA. 1979; VOL. 10; NO 12; PP. 1949-1951; BIBL. 15 REF.Article

GESTEUERTER DRUCKAUFBAU DURCH PROPORTIONAL-DRUCKVENTILE. ANWENDUNGSBEISPIEL: HYDRAULISCHE TIEFUNGS-PRUEFMASCHINE FUER BLECHE = COMMANDE DE LA MONTEE EN PRESSION PAR DES SOUPAGES PROPORTIONNELLES. EXEMPLE D'UTILISATION: MACHINE HYDRAULIQUE D'ESSAIS D'EMBOUTISSAGE DE TOLESFINDEISEN D.1979; KONSTRUKTION; DEU; DA. 1979; VOL. 31; NO 4; PP. 137-146; BIBL. 50 REF.Article

TIEFZIEHEN KONISCHER HOHLKOERPER IN EINEM HOCHDRUCKMEDIUM:STEMPELOBERFLAECHE UND SCHMIERMITTEL ENTSCHEIDEND = DEEP DRAWING OF CONICAL HOLLOW COMPONENTS IN A HIGH-PRESSURE MEDIUMBAYOUMI MR; EL SEBAIE MG.1980; BAENDER, BLECHE, ROHRE; DEU; DA. 1980-12; VOL. 21; NO 12; PP. 545-547; BIBL. 4 REF.Article

HLBOKE TAHANIE ROTACNYCH VYTAZKOV BEZ PRIDRZIAVACA V TAZNICI S OPTIMALNYM TVAROM TVORIACEJ KRIVKY = DEEP DRAWING WITHOUT BLANKHOLDERS OF ROTARY PARTSBLASCIK F; LINHARDT P.1979; STROJIRENSTVI; CSK; DA. 1979-09; VOL. 29; NO 9; PP. 550-556; BIBL. 8 REF.Article

Investigation of the influence of filler material on the deep drawing properties of lubricantsBELOSEVICH, V.K; APOSTOLOV, L.A; SERDECHNYJ, A.S et al.Kuznečno-štampovočnoe proizvodstvo (1959). 1986, Vol 28, Num 5, pp 17-18, issn 0201-7296Article

En Slovaque = Application of galvanized sheet to products with exacting formability = Anwendung von verzinktem Blech fuer Produkte mit anspruchsvollem FormaenderungsvermoegenJASOVSKÝ, F; ONDAS, M; JANOK, J et al.Hutnické listy. 1985, Vol 40, Num 1, pp 19-25, issn 0018-8069Article

Wie kann man die Umformfaehigkeit von Blechen beurteilen? = How is it possible to judge the forming capacity of sheet metals?KOLODZIEJSKI, J.Blech, Rohre, Profile. 1984, Vol 31, Num 5, pp 187-188, issn 0006-4688Article

Prove di resistenza all' ammaccatura su laminati di lega leggera = Essai d'emboutissage de tôles d'alliage léger = Deep drawing testing of light alloy sheetsAlluminio (1972). 1984, Vol 53, Num 4, pp 18-28, issn 0365-3927Article

Kerbzugversuch und anisotropes Formaenderungsvermoegen von Blechwerkstoffen = Notch tensile test and the anisotropic form change capacity of sheet metal materialsWEIST, C.Blech, Rohre, Profile. 1985, Vol 32, Num 3, pp 137-142, issn 0006-4688Conference Paper

A simple device to determine hydrogen embrittlement under biaxial tension = Dispositif simple pour déterminer la fragilité à l'hydrogène sous traction biaxialeMERLONE, G. F; OVEJERO-GARCIA, J.Scripta metallurgica. 1983, Vol 17, Num 11, pp 1315-1318, issn 0036-9748Article