Modernization of No. 2 continuous caster at Sollac Fos sur MerSERENG, G; SANERMANN, M; ZURITA, G et al.Iron & steelmaker. 2000, Vol 27, Num 11, pp 61-65, issn 0275-8687Article

Un regard sur les technologies de la coulée revêtementNISHIGORI, T.Imono. 1987, Vol 59, Num 1, pp 9-15, issn 0021-4396Article

Development of designs of slide gates and a combination of refractories for them for steel teeming ladles and tundishesDURMASHKIN, A. L; ORLOV, V. A; KORTEL, A. A et al.Refractories (New York). 1993, Vol 34, Num 5-6, pp 291-297, issn 0034-3102Article

The shrouding of top poured ingotsPETRUSHKA, R. G.Iron & steelmaker. 1991, Vol 18, Num 8, pp 41-43, issn 0275-8687, 3 p.Conference Paper

Oscillation hydraulique des lingotières en coulée continue: modulation et contrôle des cycles = Hydraulic drive for continuous casting mould oscillation. Cycles modulation and controlRADOT, J. P; MONTMAYEUR, M; PETEGNIEF, J et al.Revue de métallurgie (Paris). 1988, Vol 85, Num 1, pp 71-79, issn 0035-1563Article

Ladle Shroud as a Flow Control Device for Tundish OperationsMORALES-HIGA, Ken; GUTHRIE, R. I. L; ISAC, M et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2013, Vol 44, Num 1, pp 63-79, issn 1073-5615, 17 p.Article

Perspectives on tundish metallurgy = Aussichten zur VerteilermetallurgieTOLVE, P; PRAITONI, A; RAMACCIOTTI, A et al.Steel times. 1987, Vol 215, Num 3, issn 0039-095X, 128-129, 131-132, 134Article

Optimization of a Six-Strand Continuous Casting Tundish: Industrial Measurements and Numerical Investigation of the Tundish ModificationsMERDER, Tomasz; WARZECHA, Marek.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2012, Vol 43, Num 4, pp 856-868, issn 1073-5615, 13 p.Article

Sequential casting of mixed grades at DofascoEAVES, G. N; STEFANIK, D. P; NERI, J et al.Iron & steelmaker. 1991, Vol 18, Num 11, pp 37-41, issn 0275-8687Article

Research on the Effect of Pouring Temperature on Hot-Tear Susceptibility of A206 Alloy by SimulationMOHAMAD REZA NASRESFAHANI; MOHAMAD JAVAD RAJABLOO.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2014, Vol 45, Num 5, pp 1827-1833, issn 1073-5615, 7 p.Article

Transient fluid flow in a continuous casting tundish during ladle change and steady-state castingBOILING, Ralf; ODENTHAL, Hans-Jürgen; PFEIFER, Herbert et al.Steel research international. 2005, Vol 76, Num 1, pp 71-80, issn 1611-3683, 10 p.Article

Submersible ladle nozzles for continuous casting machines: State of the art and prospects of developmentKOLOMEITSEV, V. V; KOLOMEITSEVA, E. F; SUVOROV, S. A et al.Refractories and industrial ceramics. 2001, Vol 42, Num 5-6, pp 251-258, issn 1083-4877Article

Automation: eine mögliche Antwort auf die Strukturänderungen auch in der Druckgussindustrie. Ein BeispielJAHN, T; SCHMIDT, D.Giesserei. 1994, Vol 81, Num 9, pp 261-263, issn 0016-9765Article

Improvements in steel cleanliness by tundish inertisationBANNENBERG, N; HARSTE, K.Cahiers d'informations techniques de la revue de métallurgie. 1993, Vol 90, Num 1, pp 71-76Conference Paper

Processus d'écoulement dans les systèmes d'attaque multipleMINAMI, K; CHIJIIWA, K.Imono. 1986, Vol 58, Num 4, pp 268-274, issn 0021-4396Article

Etudes et moyens mis en œuvre à Sollac Fos pour l'augmentation des vitesses de coulée aux coulées continues = Studies and developments at Sollac Fos for the increase of continuous casting speedsFOURCADE, J. M; GUYOT, V; RAPHENNE, A et al.Revue de métallurgie (Paris). 1996, Vol 93, Num 7-8, pp IV-VII, issn 0035-1563, 11 p.Conference Paper

MDH and BGH create new horizontal continuous casting conceptWINTERHAGER, R; STADLER, P; SCHNAKENBURG, J. V et al.Iron & steelmaker. 1994, Vol 21, Num 11, pp 55-61, issn 0275-8687Article

Repeated operation of a hot tundish without preheatingISONO, K; SHIRAI, T; HIRAOKA, T et al.Iron & steelmaker. 1994, Vol 21, Num 11, pp 41-46, issn 0275-8687Article

Numerical modeling of the metallizing of intermediate ladle channels during closing of the gate valveKORTEL', A. A; SIBIKIN, V. B; LITOVSKII, E. YA et al.Refractories (New York). 1992, Vol 33, Num 1-2, pp 89-94, issn 0034-3102Article

Development of a ladle/tundish slag detectorTROTTER, D. J; DUNCAN, G; CAMPLIN, J. M et al.Iron & steelmaker. 1991, Vol 18, Num 10, pp 57-60, issn 0275-8687Conference Paper

La perméabilité des systèmes réfractaires de fermeture et de protection de jet : son rôle sur l'usure des réfractaires, la fiabilité des séquences et la propreté du métal = Permeability of the refractory systems of closing and jet protection: its part on the wear of refractories, sequences reliability and metal cleanlessGOURNAY, D; DE LORGERIL, J; MASSE, F et al.Revue de métallurgie (Paris). 1991, Vol 88, Num 1, pp 55-63, issn 0035-1563, 9 p.Conference Paper

Des installations de coulée modernes chauffées par induction en tant que pièce maîtresse de l'automatisation de la fonderieDÖTSCH, E.1990, Num 2, pp 15-22, issn 7108-5661, 8 p.Article

Jahresübersicht Leichtmetall-Sand-und Kokillenguss (36. Folge). Teil 3. Schmelzen, Giessen, Erstarren = Annual review of light-metal sand and gravity die casting (36th continuation). Part 3. Melting, Casting, SolidificationNOLTE, M.Giesserei. 1999, Vol 86, Num 2, pp 72-83, issn 0016-9765, 9 p.Article

Tundish life improvements at Armco Steel's Ashland slab casterBROWN, W. A; KINNEY, M. A; SCHADE, J et al.Iron & steelmaker. 1993, Vol 20, Num 6, pp 29-36, issn 0275-8687Conference Paper

The pursuit of steel billet qualitySAMARASEKERA, I. V; BRIMACOMBE, J. K; WILDER, K et al.Iron & steelmaker. 1994, Vol 21, Num 3, pp 53-63, issn 0275-8687Article