Curable resins based on recycled poly(ethylene terephthalate) for coating applicationsATTA, Ayman M; ABDEL-RAOUF, Manar E; ELSAEED, Shimaa M et al.Progress in organic coatings. 2006, Vol 55, Num 1, pp 50-59, issn 0300-9440, 10 p.Article

Thermal behaviour of bis-benzoxazines derived from renewable feed stock 'vanillin'SINI, N. K; BIJWE, Jayashree; VARMA, Indra K et al.Polymer degradation and stability. 2014, Vol 109, pp 270-277, issn 0141-3910, 8 p.Article

Reinforcing ability and co-catalytic effects of organo-montmorillonite clay on the epoxidized soybean oil bio-thermosetTAN, S. G; AHMAD, Z; CHOW, W. S et al.Applied clay science. 2014, Vol 90, pp 11-17, issn 0169-1317, 7 p.Article

Prediction of shape distortions. Part I. FE-implementation of a path dependent constitutive modelSVANBERG, J. Magnus; HOLMBERG, J. Anders.Composites. Part A, Applied science and manufacturing. 2004, Vol 35, Num 6, pp 711-721, issn 1359-835X, 11 p.Article

Filler dispersion evolution of acrylonitrile―butadiene rubber/graphite nanocomposites during processingLEILEI WANG; NANYING NING; LIQUN ZHANG et al.Composites. Part A, Applied science and manufacturing. 2013, Vol 47, pp 135-142, issn 1359-835X, 8 p.Article

Effect of curing conditions on strength development in an epoxy resin for structural strengtheningCZADERSKI, Christoph; MARTINELLI, Enzo; MICHELS, Julien et al.Composites. Part B, Engineering. 2012, Vol 43, Num 2, pp 398-410, issn 1359-8368, 13 p.Article

Cure behaviour and void development within rapidly cured out-of-autoclave compositesAGIUS, S. L; MAGNIEZ, K. J. C; FOX, B. L et al.Composites. Part B, Engineering. 2013, Vol 47, pp 230-237, issn 1359-8368, 8 p.Article

The effects of antifreeze use on physical and mechanical properties of concrete produced in cold weatherCULLU, Mustafa; ARSLAN, Metin.Composites. Part B, Engineering. 2013, Vol 50, pp 202-209, issn 1359-8368, 8 p.Article

Smart cure of thick composite filament wound structures to minimize the development of residual stressesDOH HOON LEE; KIM, Sun K; WOO IL LEE et al.Composites. Part A, Applied science and manufacturing. 2006, Vol 37, Num 4, pp 530-537, issn 1359-835X, 8 p.Conference Paper

Characterisation of thermoset laminates for cosmetic automotive applications: Part II - Cure and residual volatile assessmentSCHUBEL, Peter J; PARSONS, Andrew J; LESTER, Edward H et al.Composites. Part A, Applied science and manufacturing. 2006, Vol 37, Num 10, pp 1747-1756, issn 1359-835X, 10 p.Article

Material characterization of a polyester resin system for the pultrusion processBARAN, Ismet; AKKERMAN, Remko; HATTEL, Jesper H et al.Composites. Part B, Engineering. 2014, Vol 64, pp 194-201, issn 1359-8368, 8 p.Article

In situ measurements of through-the-thickness strains during processing of AS4/8552 compositeGARSTKA, Tomasz; ERSOY, N; POTTER, K. D et al.Composites. Part A, Applied science and manufacturing. 2007, Vol 38, Num 12, pp 2517-2526, issn 1359-835X, 10 p.Article

Warpage induced in bi-material specimens : Coefficient of thermal expansion, chemical shrinkage and viscoelastic modulus evolution during cureZARRELLI, Mauro; PARTRIDGE, Ivana K; D'AMORE, A et al.Composites. Part A, Applied science and manufacturing. 2006, Vol 37, Num 4, pp 565-570, issn 1359-835X, 6 p.Conference Paper

Effect of thermal residual stresses on the matrix failure under transverse compression at micromechanical level - A numerical and experimental studyCORREA, Elena; PARIS, Federico; MANTIC, Vladislav et al.Composites. Part A, Applied science and manufacturing. 2012, Vol 43, Num 1, pp 87-94, issn 1359-835X, 8 p.Article

An experimental method to study the frictional processes during composites manufacturingERSOY, Nuri; POTTER, Kevin; WISNOM, Michael R et al.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 11, pp 1536-1544, issn 1359-835X, 9 p.Article

Influence of the properties of externally bonded CFRP on the shear behavior of concrete/composite adhesive jointsFERRIER, E; QUIERTANT, M; BENZARTI, K et al.Composites. Part B, Engineering. 2010, Vol 41, Num 5, pp 354-362, issn 1359-8368, 9 p.Article

A linear finite element model to predict processing-induced distortion in FRP laminatesBAPANAPALLI, Satish K; SMITH, Lloyd V.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 12, pp 1666-1674, issn 1359-835X, 9 p.Article

Numerical analysis of cure temperature and internal stresses in thin and thick RTM partsRUIZ, Edu; TROCHU, Francois.Composites. Part A, Applied science and manufacturing. 2005, Vol 36, Num 6, pp 806-826, issn 1359-835X, 21 p.Article

Development of the properties of a carbon fibre reinforced thermosetting composite through cureERSOY, Nuri; GARSTKA, Tomasz; POTTER, Kevin et al.Composites. Part A, Applied science and manufacturing. 2010, Vol 41, Num 3, pp 401-409, issn 1359-835X, 9 p.Article

Mechanical properties of SWNT/epoxy composites using two different curing cyclesGUZMAN DE VILLORIA, R; MIRAVETE, A; CUARTERO, J et al.Composites. Part B, Engineering. 2006, Vol 37, Num 4-5, pp 273-277, issn 1359-8368, 5 p.Article