Spray coating with UV lacquers offers new opportunity for growthDETZNER, Peter; MORI, Yasuhiro.Glass (Redhill). 2004, Vol 81, Num 3, issn 0017-0984, p. 56Article

Spray Coating of Adsorbent with Polymer Latex on Sand Particles for Fluoride Removal in Drinking WaterWU, Hai-Xia; WANG, Ting-Jie; DOU, Xiao-Min et al.Industrial & engineering chemistry research. 2008, Vol 47, Num 14, pp 4697-4702, issn 0888-5885, 6 p.Article

The dynamics of particles in guniting in a twisted flowBAGRYANTSEV, V. I; NIKOLAEV, A. L; PAVLENKO, Z. YA et al.Refractories (New York). 1988, Vol 29, Num 5-6, pp 387-391, issn 0034-3102Article

A discussion: problems of the use of torch guniting for repair of the linings of thermal equipment and production of block refractory parts. Features of lining wear of chambers for dry quenching of cokeSHERSHNEV, A. A; RUSAKOV, YU. V; KULICHKOV, G. F et al.Refractories (New York). 1987, Vol 28, Num 5-6, pp 341-343, issn 0034-3102Article

A discussion: problems of the use of torch guniting for repair of the linings of thermal equipment and production of block refractory parts. Influence of refractory structure on the indices of torch gunitingRYZHOV, O. A; ERTSEVA, L. N; RUKHTAEVA, E. I et al.Refractories (New York). 1988, Vol 29, Num 5-6, pp 382-386, issn 0034-3102Article

Modeling the Deposition Dynamics of a Twin-Atomizer Spray Forming SystemZHANG, G; LI, Z; ZHANG, Y et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2010, Vol 41, Num 2, pp 303-307, issn 1073-5615, 5 p.Article

Cold Spray : A Solution for Architectural GlassVILLAFUERTE, Julio.Welding journal. 2008, Vol 87, Num 8, pp 40-42, issn 0043-2296, 3 p.Article

Microstructural Refinement within a Cold-Sprayed Copper ParticleKING, Peter C; ZAHIRI, Saden H; JAHEDI, Mahnaz et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2009, Vol 40, Num 9, pp 2115-2123, issn 1073-5623, 9 p.Article

Modeling the spray forming of H13 steel toolingYAOJUN LIN; MCHUGH, Kevin M; YIZHANG ZHOU et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2007, Vol 38, Num 7, pp 1632-1637, issn 1073-5623, 6 p.Article

Production of refractory parts by torch guniting (discussion)SHERSHNEV, A. A; CHEKRYGINA, T. M; SMIRNYI, V. V et al.Refractories (New York). 1987, Vol 28, Num 7-8, pp 405-406, issn 0034-3102Article

Verbessertes Laufverhalten von Dichtungen durch Spritzschichten = Amélioration du fonctionnement des joints d'étanchéité à l'aide de dépôts par projection = Increasing performances of seals with spray coatingNEUHAUSEN, R.VDI-Berichte. 1986, Num 624, pp 261-271, issn 0083-5560Conference Paper

Microstructure Evolution and Mechanical Behavior of Cold-Sprayed, Bulk Nanostructured TitaniumZHIMING LI; XIAOPING YANG; JUNBAO ZHANG et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2014, Vol 45, Num 11, pp 5017-5028, issn 1073-5623, 12 p.Article

Cold spray deposition of nanocrystalline aluminum alloysAJDELSZTAJN, Leonardo; JODOIN, Bertrand; KIM, George E et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2005, Vol 36, Num 3, pp 657-666, issn 1073-5623, 10 p.Article

EFFECT OF CARRIER-GAS SELECTION ON MECHANICAL PROPERTIES OF COLD-SPRAYED TANTALUMTREXLER, Matthew; CARTER, Robert; HELFRITCH, Dennis et al.International journal of powder metallurgy (1986). 2011, Vol 47, Num 5, pp 48-52, issn 0888-7462, 5 p.Conference Paper

A method of calculation of a guniting flameSHERSHNEV, A. A; BADAKH, V. F; SMYSLOV, YU. N et al.Refractories (New York). 1986, Vol 27, Num 5-6, pp 356-361, issn 0034-3102Article

Spray Forming of Bulk Ultrafine-Grained Al-Fe-Cr-TiBANJONGPRASERT, C; HOGG, S. C; LIOTTI, E et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2010, Vol 41, Num 12, pp 3208-3215, issn 1073-5623, 8 p.Article

Solidification in spray formingGRANT, P. S.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2007, Vol 38, Num 7, pp 1520-1529, issn 1073-5623, 10 p.Conference Paper

Measurements of cold spray deposition efficiencyKLLNKOVAND, S. V; KOSAREV, V. F.Journal of thermal spray technology. 2006, Vol 15, Num 3, pp 364-371, issn 1059-9630, 8 p.Article

Process of formation of a high-quality enamel coatingNIKITENKO, A. V.Glass and ceramics. 2000, Vol 57, Num 3-4, pp 143-145, issn 0361-7610Article

Blechschwingungen effektiver dämpfen : Spritzbares Dämmmaterial in der Automobilindustrie sorgt für Fertigungsflexibilität und Kostensenkungen = Use of sprayable insulating material in the automotive industryHÖLZEL, A; MANGOT, X.Farbe + Lack. 1999, Vol 105, Num 9, pp 8-9, issn 0014-7699, 4 p.Article

High efficiency promised by nozzle-free coating systemThe Glass industry. 1998, Vol 79, Num 5, pp 29-30, issn 0017-1026Article

Entwicklung eines beheizten Sprühgutträgers zum Sprühkompaktieren von Stahl = Development of a heated deposit carrier device for spray forming of steelMATTHAEI-SCHULZ, E; SCHULZ, A; VETTERS, H et al.HTM. Härterei-technische Mitteilungen. 1996, Vol 51, Num 5, pp 308-313, issn 0341-101XArticle

Life cycle assessment of ceramic spray coatings applied to boiler componentsSONOYA, K; NANBA, K; KIHARA, S et al.Ishikawajima-Harima Giho. 1996, Vol 36, Num 5, pp 382-387, issn 0578-7904Article

Thermal spray for corrosion control: a competitive edge for commercial shipbuilding. DiscussionROGERS, F. S; CALL, T.Journal of ship production. 1995, Vol 11, Num 1, pp 53-55, issn 8756-1417Conference Paper

Thermal spraying for bioceramic applicationsBERNDT, C. C; HADDAD, G. N; FARMAR, A. J. D et al.Materials forum (Rushcutters Bay). 1990, Vol 14, Num 3, pp 161-173, issn 0883-2900Article