Effect of microstructure on tensile behavior of thixoformed 357-T5 semisolid al alloyPARK, Chul; KIM, Sangshik; KWON, Yongnam et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2004, Vol 35, Num 4, pp 1407-1410, issn 1073-5623, 4 p.Article

Fracture and fatigue resistance of Mo-Si-B alloys for ultrahigh-temperature structural applicationsKRUZIC, J. J; SCHNEIBEL, J. H; RITCHIE, R. O et al.Scripta materialia. 2004, Vol 50, Num 4, pp 459-464, issn 1359-6462, 6 p.Article

Mechanical behavior of a cryomilled nanostructured Al-7.5 pct Mg alloyHAN, B. Q; MATEJCZYK, D; ZHOU, F et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2004, Vol 35, Num 3, pp 947-949, issn 1073-5623, 3 p.Article

On the suppression of dynamic embrittlement in Cu-8wt%Sn by an addition of zirconiumLIU, X. Y; KANE, W; MCMAHON, C. J et al.Scripta materialia. 2004, Vol 50, Num 5, pp 673-677, issn 1359-6462, 5 p.Article

Toughness enhancement of Ce-TZP by annealing in argonVLEUGELS, J; ZHAO, C; VAN DER BIEST, O et al.Scripta materialia. 2004, Vol 50, Num 5, pp 679-683, issn 1359-6462, 5 p.Article

Ductile-brittle transition temperature of ultrafine ferrite/cementite microstructure in a low carbon steel controlled by effective grain sizeHANAMURA, T; YIN, F; NAGAI, K et al.ISIJ international. 2004, Vol 44, Num 3, pp 610-617, issn 0915-1559, 8 p.Article

Effects of temperature and shot peening on S-N behavior of a PM Ni-base superalloy UDIMET 720LUO, J; BOWEN, P.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2004, Vol 35, Num 3A, pp 1007-1016, issn 1073-5623, 10 p.Article

The high-temperature strength of some Fe₃Al alloysMORRIS, D. G; MUNOZ-MORRIS, M. A; BAUDIN, C et al.Acta materialia. 2004, Vol 52, Num 9, pp 2827-2836, issn 1359-6454, 10 p.Article

Mechanical properties of tape cast nickel-based anode materials for solid oxide fuel cells before and after reduction in hydrogenRADOVIC, M; LARA-CURZIO, E.Acta materialia. 2004, Vol 52, Num 20, pp 5747-5756, issn 1359-6454, 10 p.Article

The effect of lamellar morphology on tensile and high-cycle fatigue behavior of orthorhombic Ti-22Al-27Nb alloyHAGIWARA, Masuo; ARAOKA, Aya; SEUNG JIN YANG et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2004, Vol 35, Num 7, pp 2161-2170, issn 1073-5623, 10 p.Article

Einfluss einer Laves-Phase auf die Kriechschädigungsprozesse in einem hochwarmfesten 9% Cr-Stahl mit Mo und B = The effect of a Laves Phase on creep damage in a high-temperature 9% Cr steel including Mo and BSTOCKER, Christian; SONNLEITNER, Roman.Praktische Metallographie. 2003, Vol 40, Num 5, pp 242-256, issn 0032-678X, 15 p.Article

Effect of precipitated Co solid solution on moisture-induced embrittlement of L1₂-type Co₃Ti ordered alloysKANENO, Y; NAKAMURA, T; INOUE, H et al.Acta materialia. 2003, Vol 51, Num 7, pp 2113-2123, issn 1359-6454, 11 p.Article

Effects of indium on the mechanical properties of ternary Sn-In-Ag soldersYEH, M. S.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2003, Vol 34, Num 2, pp 361-365, issn 1073-5623, 5 p.Article

Room temperature fracture toughness and high temperature strength of T₂/Mo_ss and (Mo, Nb)_ss/T₁/T₂ eutectic alloys in the Mo-Si-B systemITO, Kazuhiro; KUMAGAI, Michiaki; HAYASHI, Taisuke et al.Scripta materialia. 2003, Vol 49, Num 4, pp 285-290, issn 1359-6462, 6 p.Article

Scatter in fatigue life due to effects of porosity in cast A356-T6 aluminum-silicon alloysYI, J. Z; GAO, Y. X; LEE, P. D et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2003, Vol 34, Num 9, pp 1879-1890, issn 1073-5623, 12 p.Article

Slip geometry of dislocations related to cutting of the γ' phase in a new generation single-crystal superalloyZHANG, J. X; MURAKUMO, T; KOIZUMI, Y et al.Acta materialia. 2003, Vol 51, Num 17, pp 5073-5081, issn 1359-6454, 9 p.Article

The effect of solidification time and heat treatment on the fatigue properties of a cast 319 aluminum alloyBOILEAU, James M; ALLISON, John E.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2003, Vol 34, Num 9, pp 1807-1820, issn 1073-5623, 14 p.Article

The effect of loading direction and stacking sequence on the strength in quasi-isotropic CFRP laminatesNAGATA, Masamichi; TAKEZONO, Shigeo; CHEN, Jianqiao et al.Materials science research international. 2003, Vol 9, Num 2, pp 131-137, issn 1341-1683, 7 p.Article

Low- and high-cycle fatigue properties of ultrafine-grained low carbon steelsSAWAI, Tatsuaki; MATSUOKA, Saburo; TSUZAKI, Kaneaki et al.Tetsu-to-hagané. 2003, Vol 89, Num 6, pp 725-733, issn 0021-1575, 9 p.Article

The effect of modified-ausforming on giga-cycle fatigue properties in Si-Mn steelsFURUYA, Yoshiyuki; MATSUOKA, Saburo.Tetsu-to-hagané. 2003, Vol 89, Num 10, pp 1082-1089, issn 0021-1575, 8 p.Article

The influence of chemical composition and temper heat-treatment on strength and impact toughness in Ni-Cr-Mo-V steelsYOSHIOKA, Yomei; ITOU, Hiromichi; TANAKA, Yasuhiko et al.Tetsu-to-hagané. 2003, Vol 89, Num 6, pp 705-710, issn 0021-1575, 6 p.Article

An unusual fatigue phenomenon: duality of the S-N fatigue curve in the β-titanium alloy Ti-10V-2Fe-3AlJHA, S. K; RAVI CHANDRAN, K. S.Scripta materialia. 2003, Vol 48, Num 8, pp 1207-1212, issn 1359-6462, 6 p.Article

Gallium enhanced microscopy for revealing grain boundaries and dislocation subboundaries in aluminium alloysHAGSTRÖM, J; MISHIN, O. V; HUTCHINSON, B et al.Scripta materialia. 2003, Vol 49, Num 10, pp 1035-1040, issn 1359-6462, 6 p.Article

Role of dynamic strain aging on low cycle fatigue and crack propagation of type 316L(N) stainless steelDAE WHAN KIM; WOO GON KIM; RYU, Woo-Seog et al.International journal of fatigue. 2003, Vol 25, Num 9-11, pp 1203-1207, issn 0142-1123, 5 p.Conference Paper

Chemical fracture statistics and universal distribution of extreme valuesBALDASSARRI, A; GABRIELLI, A; SAPOVAL, B et al.Europhysics letters (Print). 2002, Vol 59, Num 2, pp 232-238, issn 0295-5075Article