Minimum film thicknesses in lubricated point contacts operating in the elastic piezoviscous regimeHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1988, Vol 202, Num 2, pp 73-84, issn 0263-7154Article

A note on the elastohydrodynamic lubrication of soft contactsHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1986, Vol 200, Num 3, pp 189-194, issn 0263-7154Article

The elastohydrodynamic lubrication of a cylinder on an elastomeric layerHOOKE, C. J.Wear. 1986, Vol 111, Num 1, pp 83-99, issn 0043-1648Article

The calculation of film thicknesses in soft, highly deformed contacts under dynamic conditionsHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1987, Vol 201, Num 3, pp 171-179, issn 0263-7154Article

The minimum film thickness in lubricated line contacts during a reversal of entrainment-piezoviscous behaviourHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1992, Vol 206, Num 6, pp 417-424, issn 0263-7154Article

Calculation of clearances in soft point contactsHOOKE, C. J.Journal of tribology. 1988, Vol 110, Num 1, pp 167-173, issn 0742-4787Conference Paper

The behaviour of heavily loaded line contacts with transverse roughnessHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C, Journal of mechanical engineering science. 1999, Vol 213, Num 4, pp 309-320, issn 0954-4062Article

The minimum film thickness in lubricated line contacts during a reversal of entrainment-isoviscous behaviourHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1992, Vol 206, Num 5, pp 337-345, issn 0263-7154Article

The minimum film thickness in line contacts during reversal of entrainmentHOOKE, C. J.Journal of tribology. 1993, Vol 115, Num 1, pp 191-199, issn 0742-4787Article

An interpolation procedure for the minimum film thickness in point contactsHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1990, Vol 204, Num 3, pp 199-206, issn 0263-7154, 8 p.Article

The influence of piezoviscosity on the minimlum film thickness in heavily loaded elastohydrodynamic point contactsHOOKE, C. J.Proceedings of the Institution of Mechanical Engineers. Part C. Mechanical engineering science. 1990, Vol 204, Num 2, pp 117-125, issn 0263-7154, 9 p., CArticle

The elasto-hydrodynamic lubrication of soft, highly deformed contacts under conditions of nonuniform motionHOOKE, C. J.Journal of tribology. 1986, Vol 108, Num 4, pp 545-550, issn 0742-4787Article

Considerations in the design of partially hydrostatic slipper bearingsKEG, E; HOOKE, C. J.Tribology international. 1997, Vol 30, Num 11, pp 815-823, issn 0301-679XArticle

The surface non-flatness effect on the design of bush-type bearings in high pressure pumps and motorsERDEM KOC; HOOKE, C. J.Wear. 1989, Vol 135, Num 1, pp 29-39, issn 0043-1648, 11 p.Article

End lubrication and sealing in gear pumps with fixed end platesKOC, E; HOOKE, C. J.The Journal of fluid control. 1988, Vol 18, Num 3, pp 52-69, issn 8755-8564Article

Investigation into the effects of orifice size, offset and overclamp ratio on the lubrication of slipper bearingsKOC, E; HOOKE, C. J.Tribology international. 1996, Vol 29, Num 4, pp 299-305, issn 0301-679XArticle

End plate balance in gear pumpsHOOKE, C. J; KOC, E.Proceedings of the Institution of Mechanical Engineers. Part B: management and engineering manufacture. 1984, Vol 198, Num 2, pp 55-60Article

An experimental investigation into the design and performance of hydrostatically loaded floating wear plates in gear pumpsKOC, E; HOOKE, C. J.Wear. 1997, Vol 209, Num 1-2, pp 184-192, issn 0043-1648Article

An analysis of the lubrication mechanisms of the bush-type bearings in high pressure pumpsKOC, E; KURBAN, A. O; HOOKE, C. J et al.Tribology international. 1997, Vol 30, Num 8, pp 553-560, issn 0301-679XArticle

The effects of non-flatness on the performance of slippers in axial piston pumpsHOOKE, C. J; KAKOULLIS, Y. P.Proceedings of the Institution of Mechanical Engineers. Part C: mechanical engineering science. 1983, Vol 197, pp 239-247Article

Use of the inverse approach to investigate the stresses in rough elastohydrodynamic contactsLI, K. Y; HOOKE, C. J.Journal of tribology. 2002, Vol 124, Num 1, pp 109-113, issn 0742-4787Article

Theoretical and experimental investigations of a variable-impedance hydrodynamic bearingGOODWIN, M. J; BOROOMAND, T; HOOKE, C. J et al.Tribology international. 1990, Vol 23, Num 6, pp 391-397, issn 0301-679X, 7 p.Article

A note on the lubrication of composite slippers in water-based axial piston pumps and motorsLI, K. Y; HOOKE, C. J.Wear. 1991, Vol 147, Num 2, pp 431-437, issn 0043-1648Article

Use of the inverse method to check the stress predictions in rough elastohydrodynamic lubrication contacts lubricated with a non-Newtonian fluid for a range of asperity geometriesHOOKE, C. J; LI, K. Y.Proceedings of the Institution of Mechanical Engineers. Part C, Journal of mechanical engineering science. 2003, Vol 217, Num 8, pp 935-944, issn 0954-4062, 10 p.Article

An inverse approach to the validation of pressure predictions in rough elastohydrodynamic contactsHOOKE, C. J; LI, K. Y.Journal of tribology. 2002, Vol 124, Num 1, pp 103-108, issn 0742-4787Article