Lunkerbildung in Schweissnähten = Bubble formation in welding seamsBONTEN, C; MÜLLER-JUREK, J; SCHMACHTENBERG, E et al.Plastverarbeiter. 1995, Vol 46, Num 8, pp 26-28, issn 0032-1338Article

Improving the Water Resistance of Linear Vibration-Welded Wood JointsMANSOURI, H. R; OMRANI, P; PIZZI, A et al.Journal of adhesion science and technology. 2009, Vol 23, Num 1, pp 63-70, issn 0169-4243, 8 p.Article

Improving weldline strengths of injection moulded parts by ultrasonic oscillationLIU, S.-J; LIN, K.-Y; TSAI, S.-K et al.Plastics, rubber and composites. 2008, Vol 37, Num 1, pp 23-28, issn 1465-8011, 6 p.Article

Effect of an obstacle during processing on the weld line of injection-molded glassy polystyrene: Microhardness studyNGUYEN-CHUNG, T; MENNIG, G; BOYANOVA, M et al.Journal of applied polymer science. 2004, Vol 92, Num 5, pp 3362-3367, issn 0021-8995, 6 p.Article

Polypropylene/montmorillonite nanocomposites prepared by the delamination of the fillerPOZSGAY, A; PAPP, L; FRATER, T et al.Progress in colloid & polymer science. 2001, pp 120-125, issn 0340-255X, isbn 3-540-41946-2Conference Paper

Influence of Machine Setting and Wood Parameters on Crack Formation in Scots Pine Joints Produced by Linear Friction WeldingVAZIRI, Mojgan; LINDGREN, Owe; PIZZ, Antonio et al.Journal of adhesion science and technology. 2012, Vol 26, Num 18-19, pp 2189-2197, issn 0169-4243, 9 p.Article

Analysis for diving regulator applying local heating mechanism of vapor chamber in insert molding processWANG, Jung-Chang; LI, Ai-Tsung; TSAI, Yu-Pin et al.International communications in heat and mass transfer. 2011, Vol 38, Num 2, pp 179-183, issn 0735-1933, 5 p.Article

Flow disturbance in polymer melt behind an obstacleNGUYEN-CHUNG, T; PLICHTA, C; MENNIG, G et al.Rheologica acta. 1998, Vol 37, Num 3, pp 299-305, issn 0035-4511Article

Effect of processing on weld line strength in five thermoplasticsSELDEN, R.Polymer engineering and science. 1997, Vol 37, Num 1, pp 205-218, issn 0032-3888Article

Factors affecting the shape of weld lineOHOKA, S; TAKADA, K; KIDOKORO, K et al.Kobunshi ronbunshu (Tokyo). 1996, Vol 53, Num 6, pp 339-344, issn 0386-2186Article

INFLUENCE OF NATURE AND TYPE OF FLAW ON THE PROPERTIES OF A NATURAL RUBBER COMPOUNDNGOLEMASANGO, Frederick E; O'CONNOR, Chris; MANLEY, John et al.RubberChem 2008. 2008, isbn 1-8473-5077-1 978-1-8473-5077-0, 1Vol, Q1-Q8Conference Paper

Designing plastic parts for the gas-assisted injection-moulding techniqueJOHANNABER, F; KONEJUNG, K.Polimeri (Zagreb). 1993, Vol 14, Num 6, pp 247-252, issn 0351-1871Article

Injection molding-induced morphology of thermoplastic polymer blendsZHONG, Gan-Ji; LI, Zhong-Ming.Polymer engineering and science. 2005, Vol 45, Num 12, pp 1655-1665, issn 0032-3888, 11 p.Article

Weld-line sensitivity of injected amorphous polymersDEBONDUE, E; FOURNIER, J.-E; LACRAMPE, M.-F et al.Journal of applied polymer science. 2004, Vol 93, Num 2, pp 644-650, issn 0021-8995, 7 p.Article

Development of weld line strength in injection-molded poly(methyl methacrylate)O, A. K; BRIEN-SOUCY; BARRY, C. M. F et al.The Journal of injection molding technology. 2000, Vol 4, Num 3, pp 152-158, issn 1533-905XArticle

Investigation the effects of obstacle geometries and injection molding parameters on weld line strength using experimental and finite element methods in plastic injection moldingOZCELIK, Babur; KURAM, Emel; MUSTAFA TOPAL, M et al.International communications in heat and mass transfer. 2012, Vol 39, Num 2, pp 275-281, issn 0735-1933, 7 p.Article

Advanced Injection Molding Mold and Molding Process for Improvement of Weld Line Strengths and Isotropy of Glass Fiber Filled Aromatic Polyester LCPKOPONEN, Matti; ENQVIST, Jouni; NGUYEN-CHUNG, Tham et al.Polymer engineering and science. 2008, Vol 48, Num 4, pp 711-716, issn 0032-3888, 6 p.Article

Dynamic Simulation of Fusion Process and Analysis of Flow FieldSUPEI ZHENG; JIE OUYANG; LING ZHANG et al.Journal of reinforced plastics and composites. 2007, Vol 26, Num 17, pp 1781-1792, issn 0731-6844, 12 p.Article

Effect of weld lines on the injection moulding of structural foams. II mechanical propertiesLEDUC, Simon; RODRIGUE, Denis.Cellular polymers. 2006, Vol 25, Num 2, pp 63-83, issn 0262-4893, 21 p.Article

The mechanism of ultrasonic improvement of weld line strength of injection molded polystyrene and polystyrene/ polyethylene blend partsCHANG LU; XIAOFENG YU; SHAOYUN GUO et al.Journal of polymer science. Part B. Polymer physics. 2006, Vol 44, Num 10, pp 1520-1530, issn 0887-6266, 11 p.Article

Evaluation of mechanical properties of adjacent flow weldlineYAMADA, Koji; TOMARI, Kiyotaka; ISHIAKU, Umaru Semo et al.Polymer engineering and science. 2005, Vol 45, Num 8, pp 1180-1186, issn 0032-3888, 7 p.Article

FTIR analysis of molecular orientation at weldline region in thermoplastics injection moldingTOMARI, K; HARADA, T; MAEKAWA, Z et al.Kobunshi ronbunshu (Tokyo). 1992, Vol 49, Num 7, pp 591-600, issn 0386-2186Article

Fundamental Influences on Quasistatic and Cyclic Material Behavior of Short Glass Fiber Reinforced Polyamide Illustrated on Microscopic ScaleBRUNBAUER, Julia; MÖSENBACHER, Andreas; GUSTER, Christoph et al.Journal of applied polymer science (Print). 2014, Vol 131, Num 19, issn 0021-8995, 40842.1-40842.14Article

Causes for the Improved Water Resistance in Pine Wood Linear Welded JointsMANSOURI, H. R; PIZZI, A; LEBAN, J. M et al.Journal of adhesion science and technology. 2011, Vol 25, Num 16, pp 1987-1995, issn 0169-4243, 9 p.Article

Effects of Processing Parameters on Tensile Strength of Thin-Wall HDPE Parts Injection Molded by Ultra High-Speed ProcessCHEN, Shia-Chung; LI, Hai-Mei; HSU, Pe-Ming et al.Polymer-plastics technology and engineering (Softcover ed). 2011, Vol 50, Num 1-3, pp 276-281, issn 0360-2559, 6 p.Article