Fräsbearbeitung von Druckgeissformen mit schlanken Schaftfräsern = Milling of pressure casting dies with slim shank-type cuttersKÖNIG, W; WERNER, A; LÖFFLER, R et al.Giesserei. 1992, Vol 79, Num 22, pp 922-928, issn 0016-9765Article

Influence of the Metallic Die Graphite Layer Thickness in the Microstructure of Aluminium Bronze Alloy = Einfluss der Graphitschichtdicke in der metallischen Druckgiessform auf die Mikrostruktur der Aluminium-Bronze-LegierungCENOZ, Isaac.Praktische Metallographie. 2010, Vol 47, Num 11, pp 654-664, issn 0032-678X, 11 p.Article

Druckgiessen von feinwerktechnischen Produkten = Diecasting of precision engineering productsKERN, K.F & M. Feinwerktechnik, Mikrotechnik, Messtechnik. 1993, Vol 101, Num 6, pp 247-251, issn 0944-1018Article

Theoretische Grundlagen zur Berechnung der Temperierung von Kerneinsätzen durch Wärmeleitrohre in Druckgiesswerkzeugen = Theoretical fundamentals for calculation of the tempering of core inserts through heat conducting tubes in pressure die casting diesFRIEBE, Gerhard.Giessereiforschung. 2001, Vol 53, Num 4, issn 0046-5933, 130, 170-178 [9 p.]Article

Performances comparées de douze nouveaux traitements de surface anti-collage sous pression = Performance comparison of twelve new anti-soldering surface treatments for high pressure die castingHAIRY, P; DUSSAUSSOIS, R; CORSON, B et al.Fonderie, Fondeur d'aujourd'hui. 2003, Num 227, pp 30-43, issn 0249-3136, 14 p.Article

One-dimensional heat flow analysis of die casting dies by temperature boundary conditionsODA, K; ANZAI, K; NIYAMA, E et al.Chuzo kogaku. 1996, Vol 68, Num 9, pp 746-752, issn 1342-0429Article

Softwaremodul zur Prozessauslegung der Fräsbearbeitung mit schalanken Schaftfräsern im Druckgiessformenbau = Software modules for the process control in machining of pressure casting dies with slim Shank-type clustersKPNIG, W; WERNER, A; LÖFFER, R et al.Giesserei. 1994, Vol 81, Num 5, pp 128-132, issn 0016-9765Article

Diecasting quality starts with the diesSMITH, W. E.Foundry management & technology. 1991, Vol 119, Num 7, pp 41-44, issn 0360-8999, 4 p.Article

Le moulage sous pression des alliages d'aluminium (Fascicule 5, Le travail thermique du moule)Hugot, Pierre.2000, isbn 2-7119-0186-6, 46 p., isbn 2-7119-0186-6Book

Heat-Transfer Coefficient and In-Cavity Pressure at the Casting-Die Interface during High-Pressure Die Casting of the Magnesium Alloy AZ91DHAMASAIID, A; DOUR, G; DARGUSCH, M. S et al.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2008, Vol 39, Num 4, pp 853-864, issn 1073-5623, 12 p.Article

Quantification des défauts en fonderie sous pression (partie I) Analyse sur micrographie et dimension fractale des retassures = Quantification of defects in pressure die casting (part One) Analysis on micrograph and fractal dimension of shrinkage cavitiesHAIRY, Patrick.Fonderie, Fondeur d'aujourd'hui. 2007, Num 265, pp 12-25, issn 0249-3136, 14 p.Article

Effects of casting pressure on deformation of gas porosity in aluminum die castingTANIKAWA, Shoji; ASAI, Koichi; YI YANG et al.Chuzo kogaku. 2005, Vol 77, Num 3, pp 161-166, issn 1342-0429, 6 p.Article

Design limits of unbonded laminate tooling for pressure die-castingSOAR, R; DICKENS, P.Proceedings of the Institution of Mechanical Engineers. Part B. Journal of engineering manufacture. 2001, Vol 215, Num 4, pp 531-543, issn 0954-4054Article

PVD-Beschichtungen verlängern die Lebensdauer von Druckgiessformen = PVD plating increases the service life of pressure die casting diesWILD, R.Giesserei. 1993, Vol 80, Num 20, pp 696-699, issn 0016-9765Article

Significance of friability as an important property of high pressure moulding sand = Signification de la fiabilité comme propriété importante d'un sable de moulage haute pressionVENKOBA RAO, T. S; ROSHAN, H. MD.Transactions of the Indian Institute of Metals. 1988, Vol 41, Num 4, pp 357-362, issn 0019-493XArticle

Comment éviter le collage en fonderie sous pression = Preventing soldering in pressure die castingTOMASEVIC, Didier; LONGA, Yves; TURREL, Jean-Philippe et al.Fonderie magazine. 2011, Num 20, pp 19-32, issn 2106-7635, 14 p.Article

Formation of gas induced shrinkage porosity in Mg-alloy high-pressure die-castingsSOON GI LEE; GOKHALE, Arun M.Scripta materialia. 2006, Vol 55, Num 4, pp 387-390, issn 1359-6462, 4 p.Article

Mechanical properties of saffil fiber reinforced zinc-aluminium alloy (ZA 27) produced by pressure die castingKURNAZ, S. Can; DURMAN, Mehmet.Zeitschrift für Metallkunde. 2005, Vol 96, Num 1, pp 54-61, issn 0044-3093, 8 p.Article

Modelling the pressure die casting process with the boundary element method : die deformation model for flash preventionMILROY, J; HINDUJA, S; DAVEY, K et al.Proceedings of the Institution of Mechanical Engineers. Part C, Journal of mechanical engineering science. 1998, Vol 212, Num 3, pp 197-215, issn 0954-4062Article

Conception et exploitation des moules en fonderie sous pression = Design and use of pressure casting diesDE RUFFRAY, J.Fonderie, Fondeur d'aujourd'hui. 2003, Num 222, pp 39-45, issn 0249-3136, 7 p.Article

CAD/CAM aspects in diemakingHEUEL, O.1986, Vol 4, Num 4, issn 0177-1469, 2,4,6,8,11Article

The runner optimisation design of a die-casting die and the part producedLIN, J. C; TAI, C. C.International journal, advanced manufacturing technology. 1998, Vol 14, Num 2, pp 133-145, issn 0268-3768Article

Effects of molten aluminum on H13 dies and coatingsYU, M; SHIVPURI, R; RAPP, R. A et al.Journal of materials engineering and performance. 1995, Vol 4, Num 2, pp 175-181, issn 1059-9495Article

Investigating ion nitriding for the reduction of dissolution and soldering in die-casting shot sleevesJOSHI, Vivek; SRIVASTAVA, Amit; SHIVPURI, Rajiv et al.Surface & coatings technology. 2003, Vol 163-64, pp 668-673, issn 0257-8972, 6 p.Conference Paper

Essais industriels de quatre traitements de surface de moules en fonderie sous pression = Industrial tests of four die surface treatementHAIRY, P.Fonderie, Fondeur d'aujourd'hui. 1995, Num 146, pp 2-3, issn 0249-3136, 8 p.Article