PROPRIETES DE TOLES FORTES EN ALLIAGE ALMGSIKOMAREK V; OCENASEK V.1975; HUTN. LISTY; CESKOSL.; DA. 1975; VOL. 30; NO 6; PP. 412-418; ABS. RUSSE ALLEM. ANGL. FR.; BIBL. 6 REF.Article

RECRISTALLISATION ET RESTAURATION DE AL ET CU EN FONCTION DE LA TEMPERATURE DE DEFORMATION (-I)OCENASEK V; SEDLACEK V.1977; KOVOVE MATER.; CESKOSL.; DA. 1977; VOL. 15; NO 3; PP. 269-280; ABS. RUSSE ANGL.; BIBL. 13 REF.Article

VLIV OLOVA NA TVAR TRISKY U TYCI ZE SLITINY MS59PB:VLIV OBSAHU OLOVA NA TVAR TRISKY. STANOVENI OPTIMALNIHO OBSAHU OLOVA VE SLITINE MS59PB = EFFECT OF LEAD ON CHIP SHAPE IN MS59PB BRASS ALLOY BARSSPERLINK K; OCENASEK V; SKLENAROVA J et al.1979; HUTN. LISTY; CSK; DA. 1979-08; VOL. 34; NO 8; PP. 542-547; BIBL. 13 REF.Article

Polarized light microscopy: utilization in the investigation of the recrystallization of aluminum alloysSLAMOVA, M; OCENASEK, V; VOORT, G. Vander et al.Materials characterization. 2004, Vol 52, Num 3, pp 165-177, issn 1044-5803, 13 p.Article

Creep behaviour of the creep resistant MgY3Nd2ZnlMnl alloyHNILICA, F; JANIK, V; SMOLA, B et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2008, Vol 489, Num 1-2, pp 93-98, issn 0921-5093, 6 p.Article

Inhomogeneity of mechanical properties and deformation instabilities in Al-Cu-Li-Mg alloyCIESLAR, M; VOSTRY, P; OCENASEK, V et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 1997, Vol 234-36, pp 790-793, issn 0921-5093Conference Paper

An evaluation of fatigue crack growth and affecting mechanisms in Al-alloys with strongly orientated microstructureCERNY, I; OCENASEK, V; HNILICA, F et al.International Conference on Damage and Fracture Mechanics. 2004, pp 103-112, isbn 1-85312-707-8, 1Vol, 10 p.Conference Paper

Impact of as-cast structure on structure and properties of twin-roll cast AA8006 alloySLAMOVA, M; JURICEK, Z; OCENASEK, V et al.Materials science forum. 2000, pp 161-166, issn 0255-5476, isbn 0-87849-853-2, 3VolConference Paper

Influence of annealing duration on properties of AlLiCuMg thin-walled extruded shapesOCENASEK, V; SLAMOVA, M; SPERLINK, K et al.Journal de physique. IV. 1993, Vol 3, Num 7, pp 219-225, issn 1155-4339, 1Conference Paper

Differences in structure evolution of twin-roll cast AA8006 and AA8011 alloys during annealingSLAMOVA, M; OCENASEK, V; CIESLAR, M et al.Materials science forum. 2000, pp 829-834, issn 0255-5476, isbn 0-87849-853-2, 3VolConference Paper

Precipitation in cold-rolled Al-Sc-Zr and Al-Mn-Sc-Zr alloys prepared by powder metallurgyVLACH, M; STULIKOVA, I; NEUBERT, V et al.Materials characterization. 2013, Vol 86, pp 59-68, issn 1044-5803, 10 p.Article