Bend allowance and developed length calculation for pressbrake bendingPOURBOGHRAT, F; STELSON, K. A.Journal of manufacturing science and engineering. 1997, Vol 119, Num 2, pp 227-237, issn 1087-1357Article

An efficient algorithm for shortest path in three dimensions with polyhedral obstaclesKHOURI, J; STELSON, K. A.Journal of dynamic systems, measurement, and control. 1989, Vol 111, pp 433-436, issn 0022-0434Article

Smoothing curvature and torsion with spring splinesWAGNER, P. H; LUO, X; STELSON, K. A et al.Computer-aided design. 1995, Vol 27, Num 8, pp 615-626, issn 0010-4485Article

A approximate model to calculate foldover and strains during cold upsetting of cylinders. II, Use of the foldover model to estimate frictionETTOUNEY, O. M; STELSON, K. A.Journal of engineering for industry. 1990, Vol 112, Num 3, pp 267-271, issn 0022-0817Article

Modeling and control of the in-situ thermoplastic composite tape-laying processSUR, W.-C; MANTELL, S. C; STELSON, K. A et al.Journal of dynamic systems, measurement, and control. 1998, Vol 120, Num 4, pp 507-515, issn 0022-0434Article

Analysis of flow patterns and solidification phenomena in the die casting processMINAIE, B; STELSON, K. A; VOLLER, V. R et al.Journal of engineering materials and technology. 1991, Vol 113, Num 3, pp 296-302, issn 0094-4289Article

An approximate model to calculate foldover and strains during cold upsetting of cylinders. I, Formulation and evaluation of the foldover modelETTOUNEY, O. M; STELSON, K. A.Journal of engineering for industry. 1990, Vol 112, Num 3, pp 260-266, issn 0022-0817Article

Control of the fabrication of long slender workpieces of arbitrary shape-Part I: Open-loop control of the multi-axis bending processLUO, J. X; JOYNT, D. L; STELSON, K. A et al.Journal of dynamic systems, measurement, and control. 1996, Vol 118, Num 3, pp 540-548, issn 0022-0434Article

Prediction of filling time and vent locations for resin transfer moldsCHEN, Y. F; STELSON, K. A; VOLLER, V. R et al.Journal of composite materials. 1997, Vol 31, Num 11, pp 1141-1161, issn 0021-9983Article

Fabrication of carbon nanotube based transparent conductive thin films using layer-by-layer technologyYU, X; RAJAMANI, R; STELSON, K. A et al.Surface & coatings technology. 2008, Vol 202, Num 10, pp 2002-2007, issn 0257-8972, 6 p.Article

Carbon nanotube based transparent conductive thin filmsYU, X; RAJAMANI, R; STELSON, K. A et al.Journal of nanoscience and nanotechnology (Print). 2006, Vol 6, Num 7, pp 1939-1944, issn 1533-4880, 6 p.Article

Time-implicit fixed and deforming grid solutions for compression mold fillingCHEN, Y. F; VOLLER, V. R; STELSON, K. A et al.Polymer composites. 1996, Vol 17, Num 3, pp 414-422, issn 0272-8397Article

An approximate model of residual stress in injected molded partsZHANG, X; VOLLER, V. R; STELSON, K. A et al.International conference on computational structures technologyInternational conference on engineering computational technology. 2000, pp 273-277, isbn 0-948749-67-9Conference Paper

Computer-aided process planning for turned parts using fundamental and heuristic principlesKORDE, U. P; BORA, B. C; STELSON, K. A et al.Journal of engineering for industry. 1992, Vol 114, Num 1, pp 31-40, issn 0022-0817Article

Approximate model of thermal residual stress in an injection molded partZHANG, X; CHENG, X; STELSON, K. A et al.Journal of thermal stresses. 2002, Vol 25, Num 6, pp 523-538, issn 0149-5739Article