Influence of grinding parameters on Si₃N₄ ceramic mechanical propertiesRODRIGUEZ, R; LERICHE, A; CARREROT, H et al.Silicates industriels. 2004, Num 7-8, pp 325-332, issn 0037-5225, 8 p.Conference Paper

Characterisation of porous silicon nitride materials produced with starchDIAZ, Aranzazu; HAMPSHIRE, Stuart.Journal of the European Ceramic Society. 2004, Vol 24, Num 2, pp 413-419, issn 0955-2219, 7 p.Conference Paper

Subcritical crack growth in SiAlON ceramics from a modified static lifetime test including multiple use of survivalsRIVA, M; HOFFMANN, M. J; OBERACKER, R et al.Journal of materials science. 2008, Vol 43, Num 1, pp 402-405, issn 0022-2461, 4 p.Article

Precipitation Coating of Monazite on Woven Ceramic Fibers. II. Effect of Processing Conditions on Coating Morphology and Strength Retention of Nextel^TM 610 and 720 FibersFAIR, Geoff E; HAY, Randall S; BOAKYE, Emmanuel E et al.Journal of the American Ceramic Society. 2008, Vol 91, Num 5, pp 1508-1516, issn 0002-7820, 9 p.Article

Synthesis of mono-phase, hexagonal plate-like Al₄SiC₄ powder via a carbothermal reduction processLEE, Jin-Seok; LEE, Sea-Hoon; NISHIMURA, Toshiyuki et al.Nippon seramikkusu kyokai gakujutsu ronbunshi. 2008, Vol 116, Num 6, pp 717-721, issn 0914-5400, 5 p.Conference Paper

On the preparation of bio-, nano- and structural ceramics and composites by spark plasma sinteringNYGREN, Mats; ZHIJIAN SHEN.Solid state sciences. 2003, Vol 5, Num 1, pp 125-131, issn 1293-2558, 7 p.Article

Ti₃SiC₂/Al₂O₃ composites prepared by SPSWANG, H. J; JIN, Z. H; MIYAMOTO, Y et al.Ceramics international. 2003, Vol 29, Num 5, pp 539-542, issn 0272-8842, 4 p.Article

Water vapor corrosion of mullite : Single crystals versus polycrystalline ceramicsSCHMUCKER, Martin; MECHNICH, Peter; ZAEFFERER, Stefan et al.Journal of the European Ceramic Society. 2008, Vol 28, Num 2, pp 425-429, issn 0955-2219, 5 p.Conference Paper

Microstmcture and high temperature 4-point bending creep of sol-gel derived mullite ceramicsIVANKOVIC, Hrvoje; TKALCEC, Emilija; REIN, Ruediger et al.Journal of the European Ceramic Society. 2006, Vol 26, Num 9, pp 1637-1646, issn 0955-2219, 10 p.Article

Advanced (electro) ceramics and innovative energy technologiesANTONUCCI, Vincenzo; ANTONUCCI, Pier Luigi; GULLO, Laura et al.Journal of the European Ceramic Society. 2004, Vol 24, Num 6, pp 1337-1342, issn 0955-2219, 6 p.Conference Paper

Controlled porosity in silicon nitride ceramics and its effects on propertiesDIAZ, A; HAMPSHIRE, S.Silicates industriels. 2004, Num 7-8, pp 205-209, issn 0037-5225, 5 p.Conference Paper

Experimental design applied to silicon carbide sinteringMARCHI, Juliana; BRESSIANI, José Carlos; BRESSIANI, Ana Helena De A et al.Journal of the American Ceramic Society. 2003, Vol 86, Num 7, pp 1208-1210, issn 0002-7820, 3 p.Article

The influence of Cr on fracture toughness and microstructure of Fe-Al/Al₂O₃ compositeLI, A; SUN, K; YIN, Y et al.Interceram. 2003, Vol 52, Num 5, pp 284-288, issn 0020-5214, 3 p.Article

Tribological tests verify wear resistanceKERKWIJK, B; BUIZERT, J. J. C; VERWEIJ, H et al.American Ceramic Society bulletin. 2000, Vol 79, Num 1, pp 49-53, issn 0002-7812Article

Refereed Reports Oxide-Oxide Composites, Irsee, Germany, 22-24 June 1998SCHNEIDER, H.Journal of the European Ceramic Society. 2000, Vol 20, Num 5, issn 0955-2219, 130 p.Conference Proceedings

Mechanical properties and damage tolerance of Y₂SiO₅ZIQI SUN; JINGYANG WANG; MEISHUAN LI et al.Journal of the European Ceramic Society. 2008, Vol 28, Num 15, pp 2895-2901, issn 0955-2219, 7 p.Article

Oxygen ionic transport in SrFe1-yAlyO3-δ and Sr1-xCaxFe0.5Al0.5O3-δ ceramicsSHAULA, A. L; KHARTON, V. V; VYSHATKO, N. P et al.Journal of the European Ceramic Society. 2005, Vol 25, Num 4, pp 489-499, issn 0955-2219, 11 p.Article

Phase formation in porous liquid phase sintered silicon carbide. Part I: Interaction between Al₂O₃ and SiCIHLE, J; HERRMANN, M; ADLER, J et al.Journal of the European Ceramic Society. 2005, Vol 25, Num 7, pp 987-995, issn 0955-2219, 9 p.Article

Phase formation in porous liquid phase sintered silicon carbide. Part III: Interaction between Al₂O₃-Y₂O₃ and SiCIHLE, J; HERRMANN, M; ADLER, J et al.Journal of the European Ceramic Society. 2005, Vol 25, Num 7, pp 1005-1013, issn 0955-2219, 9 p.Article

Micromecanizado de materiales cerámicos mediante láser de femtosegundo = Femtosecond laser micromachining of ceramicsMORENO, P; MENDEZ, C; GARCIA, A et al.Boletín de la Sociedad Española de Cerámica y Vidrio. 2005, Vol 44, Num 1, pp 9-12, issn 0366-3175, 4 p.Article

3D fine scale ceramic components formed by ink-jet prototyping processNOGUERA, Rémi; LEJEUNE, Martine; CHARTIER, Thierry et al.Journal of the European Ceramic Society. 2005, Vol 25, Num 12, pp 2055-2059, issn 0955-2219, 5 p.Conference Paper

Development of WC-ZrO₂ nanocomposites by spark plasma sinteringBASU, Bikramjit; LEE, Jong-Heun; KIM, Doh-Yeon et al.Journal of the American Ceramic Society. 2004, Vol 87, Num 2, pp 317-319, issn 0002-7820, 3 p.Article

Novel assemblies via spark plasma sinteringNYGREN, Mats; ZHIJIAN SHEN.Silicates industriels. 2004, Num 7-8, pp 211-218, issn 0037-5225, 8 p.Conference Paper

Ceramic components for environmentally friendly internal combustion enginesTHIEMANN, K.-H; SCHÄFER, W.CFI. Ceramic forum international. 2003, Vol 80, Num 8, pp E15-E20, issn 0173-9913Article

Anisotropic grain growth of mullite in high-energy ball milled powders doped with transition metal oxidesKONG, L. B; ZHANG, T. S; MA, J et al.Journal of the European Ceramic Society. 2003, Vol 23, Num 13, pp 2247-2256, issn 0955-2219, 10 p.Article