Crack length and J-integral expressions for specimens loaded in tensionFAUCHER, B.Journal of testing and evaluation. 1994, Vol 22, Num 1, pp 30-35, issn 0090-3973Article

Numerical assessment of the dynamic tension test using the split Hopkinson barRODRIGUEZ, J; NAVARRO, C; SANCHEZ-GALVEZ, V et al.Journal of testing and evaluation. 1994, Vol 22, Num 4, pp 335-342, issn 0090-3973Article

Tensile properties of Mg-8Al-xRE alloys from 300 K to 673 KYANG, Wan-Gye; KOO, Chun-Hao.Materials transactions - JIM. 2003, Vol 44, Num 5, pp 1029-1035, issn 0916-1821, 7 p.Article

Influence of post weld heat treatment on the Dynamic Strain Aging of C-Mn steelsWAGNER, D; MORENO, J. C; PRIOUL, C et al.Journal de physique. IV. 1996, Vol 6, Num 8, pp C8.159-C8.162, issn 1155-4339Conference Paper

Formation of recrystallized grains at grain boundaries of copper bicrystals deformed in tensionINOKO, F; YOSHIKAWA, T.Materials transactions - JIM. 1993, Vol 34, Num 4, pp 334-342, issn 0916-1821Article

Deformation and failure mechanisms in graphene oxide paper using in situ nanomechanical tensile testingCONGWEI WANG; FROGLEY, Mark D; CINQUE, Gianfelice et al.Carbon (New York, NY). 2013, Vol 63, pp 471-477, issn 0008-6223, 7 p.Article

A practical constitutive model covering a wide range of strain rates and a large region of strainTANIMURA, S; HAYASHI, H; YAMAMOTO, T et al.Journal de physique. IV. 2006, Vol 134, pp 55-61, issn 1155-4339, 7 p.Conference Paper

Distribution of the grain size of ferrite in the deformation zone of 18G2A (A 765-94 ASTM) steel samples after tensile tests and recrystallizationWAWSZCZAK, Jerzy.Materials characterization. 2001, Vol 46, Num 2-3, pp 143-147, issn 1044-5803Article

ANALYSE DES MECANISMES D'ENDOMMAGEMENT DANS LES COMPOSITES 3D C/C. MESURES OPTIQUES DES CHAMPS DE DEFORMATION PAR CORRELATION D'IMAGE = ANALYSIS OF DAMAGE MECHANISMES IN 3D C/C COMPOSITES. OPTICAL MEASUREMENTS OF STRAINS USING AN IMAGE CORRELATION METHODTardif, Fabrice; Lamon, Jacques.1998, 150 p.Thesis

Etudes par photoélasticimétrie de composites modèles soumis à des efforts de traction et de compression = Photoelastic analysis in carbon fibre model composites under axial compressive or traction stressesAndrieux, Marc; Sixou, P.1994, 165 p.Thesis

Fracture properties of bambooAMADA, Shigeyasu; UNTAO, Sun.Composites. Part B, Engineering. 2001, Vol 32, Num 5, pp 451-459, issn 1359-8368Article

Effect of stress concentration on rupture strengthSHESTERIKOV, S. A; LOKOSHCHENKO, A. M.Strength of materials. 1996, Vol 28, Num 5, pp 358-360, issn 0039-2316Article

Shear strength testing of solid oxygenBATES, S. C; ALTSHULER, T. L.Cryogenics (Guildford). 1995, Vol 35, Num 9, pp 559-566, issn 0011-2275Article

Analysis of crack branching morphology in a disk of brittle material under axisymmetric tension by using branching dimensionNAKASA, K; NAKATSUKA, J.-I.Engineering fracture mechanics. 1994, Vol 47, Num 3, pp 403-415, issn 0013-7944, 12 p.Article

Statistical distribution of tensile strength in carbon fiberTAGAWA, T; TANIGUCHI, M; MIYATA, T et al.Zairyo. 1993, Vol 42, Num 479, pp 955-961, issn 0514-5163Article

Simulations of necking during plane strain tensile testsDALLE, F.Journal de physique. IV. 2006, Vol 134, pp 429-434, issn 1155-4339, 6 p.Conference Paper

Dynamic characterization of carboxymethyl cellulosic nonwoven material in the environmental scanning electron microscopeWEI, Q. F; WANG, X. Q.Materials characterization. 2005, Vol 55, Num 2, pp 148-152, issn 1044-5803, 5 p.Article

Damage and rupture in sintered aluminaNAJAR, J; SILBERSCHMIDT, V. V.Advances in science and technology. 1999, pp A641-A648, isbn 88-86538-14-6, 5VolConference Paper

Determination of the origin for the dissymmetry observed between tensile and compression tests on shape memory alloysPATOOR, E; EL AMRANI, M; EBERHARDT, A et al.Journal de physique. IV. 1995, Vol 5, Num 2, pp C2.495-C2.500, issn 1155-4339Conference Paper

Intermetallic embrittlement of thin unsupported Tin/Copper specimensFREEMAN, G. B; LIVESAY, B. R; BRADLEY, J et al.Journal of electronic materials. 1994, Vol 23, Num 9, pp 919-924, issn 0361-5235Article

Local stability loss and failure of cracked plates during the plastic deformation of materialsDYSHEL', M. SH.International applied mechanics. 1994, Vol 30, Num 1, pp 44-47, issn 1063-7095Article

Texture investigation of the superelastic Ti―24Nb―4Zr―8Sn alloyYANG, Y; CASTANY, P; CORNEN, M et al.Journal of alloys and compounds. 2014, Vol 591, pp 85-90, issn 0925-8388, 6 p.Article

Whole-field analysis of uniaxial tensile tests by Moiré interferometryCORDERO, Raul R; FRANCOIS, Manuel; LIRA, Ignacio et al.Optics and lasers in engineering. 2005, Vol 43, Num 9, pp 919-936, issn 0143-8166, 18 p.Article

Modeling of hardening and softening processes in Mg alloysMATHIS, K; TROJANOVA, Z; LUKAC, P et al.Journal of alloys and compounds. 2004, Vol 378, pp 176-179, issn 0925-8388, 4 p.Conference Paper

Effect of wall angle on Al3003 strain hardening for parts formed by computer numerical control incremental formingHAGAN, E; JESWIET, J.Proceedings of the Institution of Mechanical Engineers. Part B. Journal of engineering manufacture. 2003, Vol 217, Num 11, pp 1571-1579, issn 0954-4054, 9 p.Article