Process simulation and optimization for injection molding: Experimental verifications and field applicationsTURNG, Lih-Sheng; PEIC, Michael; BRADLEY, Dave K et al.The Journal of injection molding technology. 2002, Vol 6, Num 2, pp 143-155, issn 1533-905XArticle

The impact behavior of weld-lines in injection moldingVIANA, J. C; CUNHA, A. M.The Journal of injection molding technology. 2002, Vol 6, Num 4, pp 259-271, issn 1533-905X, 13 p.Article

An assessment of Dynamic Feed control in modular toolingREILLY, Jim F; DOYLE, Mark; KAZMER, David O et al.The Journal of injection molding technology. 2001, Vol 5, Num 1, pp 49-60, issn 1533-905XArticle

Predictive control of cavity pressure during injection fillingDUBAY, Rickey.The Journal of injection molding technology. 2001, Vol 5, Num 2, pp 72-79, issn 1533-905XArticle

Testing and evaluation of a T-type cantilever snap-fit in an automotive sealing environmentLUSCHER, Anthony; HALE, Aaron.The Journal of injection molding technology. 2001, Vol 5, Num 2, pp 120-131, issn 1533-905XArticle

A study on volumetric shrinkage of injection molded parts based on neural networksMIN, Byeong-Hyeon; SHIN, Byoung-Chul.The Journal of injection molding technology. 2001, Vol 5, Num 4, pp 201-207, issn 1533-905XArticle

Development of a new injection molding technology: Momentary Mold Surface Heating processKIM, Dong-Hak; KANG, Myung-Ho; CHUN, Y. H et al.The Journal of injection molding technology. 2001, Vol 5, Num 4, pp 229-232, issn 1533-905XArticle

Evaluation of liquid gas-assisted injection moldingKIM, Dong-Hak; DO YOUNG MOON; SEONG JAE LEE et al.The Journal of injection molding technology. 2001, Vol 5, Num 4, pp 224-228, issn 1533-905XArticle

Special and emerging injection molding processesTURNG, Lih-Sheng.The Journal of injection molding technology. 2001, Vol 5, Num 3, pp 160-179, issn 1533-905XArticle

Predicting flow length of spiral melt flows in injection molds by a semi-empirical modelRAO, N. S; SCHUMACHER, G; MA, C.-T et al.The Journal of injection molding technology. 2000, Vol 4, Num 2, pp 92-96, issn 1533-905XArticle

An investigation of the geometry and transmission error of injection molded gearsLUSCHER, Anthony; HOUSER, Donald; SNOW, Chris et al.The Journal of injection molding technology. 2000, Vol 4, Num 4, pp 177-190, issn 1533-905XArticle

A numerical approach for predicting the optical characteristics of injection-molded lensesKIM, S. Y; RIM, M. H; LIM, W. S et al.The Journal of injection molding technology. 2000, Vol 4, Num 1, pp 29-35, issn 1533-905XArticle

Prediction of stiffness from orientation data of glass reinforced injection moldingsNEVES, N. M; POUZADA, A. S.The Journal of injection molding technology. 1999, Vol 3, Num 3, pp 126-132, issn 1533-905XArticle

An approximate prediction of sink mark depth in rib-reinforced plastic parts by empirical equationsLINHUO SHI; GUPTA, M.The Journal of injection molding technology. 1999, Vol 3, Num 1, pp 1-10, issn 1533-905XArticle

Effect of reprocessing and moisture on the properties of bisphenol-A polycarbonateAGUIRRE-FLORES, R; SANCHEZ-VALDES, S.The Journal of injection molding technology. 1999, Vol 3, Num 1, pp 21-26, issn 1533-905XArticle

Troubleshooting cavity to cavity variations in multi-cavity injection moldsBEAUMONT, J; RALSTON, J; SHUTTLEWORTH, A et al.The Journal of injection molding technology. 1999, Vol 3, Num 2, pp 88-98, issn 1533-905XArticle

Application examples for gas-assisted injection molded partsHANSEN, M.The Journal of injection molding technology. 1999, Vol 3, Num 3, pp 141-153, issn 1533-905XArticle

Use of servo robots for injection molding applicationsMALLON, J. M.The Journal of injection molding technology. 1998, Vol 2, Num 2, pp 95-101, issn 1533-905XArticle

A localized shrinkage analysis for predicting sink marks in injection-molded plastic partsLINHUO SHI; GUPTA, M.The Journal of injection molding technology. 1998, Vol 2, Num 4, pp 149-155, issn 1533-905XArticle

Development of a methodology for defect reduction in injection molding using process simulations. Part II : A multi-factor design of experiments approachPATEL, S. A; MALLICK, P. K.The Journal of injection molding technology. 1998, Vol 2, Num 4, pp 184-191, issn 1533-905XArticle

An improved mold pin gate and its flow pattern in the cavityWENLI DAI; PENGSHENG LIU; XIAYU WANG et al.The Journal of injection molding technology. 2002, Vol 6, Num 2, pp 115-119, issn 1533-905XArticle

Self-learning control for injection molding based on neural networks optimizationLIANG, Jui-Ming; WANG, Pei-Jen.The Journal of injection molding technology. 2002, Vol 6, Num 1, pp 58-71, issn 1533-905XArticle

Design Sensitivity Analysis for gas-assisted injection moldingILINCA, Florin; HETU, Jean-Francois.The Journal of injection molding technology. 2002, Vol 6, Num 3, pp 194-202, issn 1533-905X, 9 p.Article

Experimental study of gas penetration in gas-assisted injection moldingSHIN, Jin-Woong; ISAYEV, A. I.The Journal of injection molding technology. 2002, Vol 6, Num 4, pp 314-330, issn 1533-905X, 17 p.Article

Injection molding of poly(ethylene terephthalate)/poly(butylene terephthalate) reinforced with thermotropic liquid crystalline polymer microfibrilsBAIRD, Donald G; JIANHUA HUANG.The Journal of injection molding technology. 2002, Vol 6, Num 4, pp 297-304, issn 1533-905X, 8 p.Article