Improving diamond coating on Ti6A14V substrate using a diamond like carbon interlayer: Raman residual stress evaluation and AFM analysesNIBENNANOUNE, Z; GEORGE, D; ANTONI, F et al.Diamond and related materials. 2012, Vol 22, pp 105-112, issn 0925-9635, 8 p.Article

Mechanical properties of Ti(C_0.7N_0.3) film produced by plasma electrolytic carbonitriding of Ti6A14V alloyLI, Xin-Mei; YONG HAN.Applied surface science. 2008, Vol 254, Num 20, pp 6350-6357, issn 0169-4332, 8 p.Article

The effect of gold pre-deposition on the oxidation behavior of CPTi and Ti6Al4V alloyZHANG, Z. X; DONG, H; BELL, T et al.Oxidation of metals. 2006, Vol 66, Num 1-2, pp 91-106, issn 0030-770X, 16 p.Article

In vitro effect of magnesium inclusion in sol-gel derived apatiteGUOCHAO QI; ZHANG, Sam; KHOR, K. A et al.Thin solid films. 2008, Vol 516, Num 16, pp 5176-5180, issn 0040-6090, 5 p.Conference Paper

Influencia del arenado de la aleación Ti6Al4V en la dureza subsuperficial y estado de tensiones residuales = Influence of sandblasting of Ti6Al4V alloy on the subsurface hardness and residual stresses stateMULTIGNER, M; FEMANDEZ-CASTRILLO, P; FERREIRA-BARRAGANS, S et al.Revista de metalurgia (Madrid). 2009, Vol 45, Num 1, pp 52-57, issn 0034-8570, 6 p.Article

Deposition of Ti-6Al-4V using a high power diode laser and wire, Part I Investigation on the process characteristicsSUI HIM MOK; GUIJUN BI; FOLKES, Janet et al.Surface & coatings technology. 2008, Vol 202, Num 16, pp 3933-3939, issn 0257-8972, 7 p.Article

Enhanced tribological behavior of anodic films containing SiC and PTFE nanoparticles on Ti6A14V alloySONGMEI LI; MENGQI ZHU; JIANHUA LIU et al.Applied surface science. 2014, Vol 316, pp 28-35, issn 0169-4332, 8 p.Article

The load bearing capacity of hydrogen-free Cr-DLC coatings on deep-case oxygen hardened Ti6Al4VZHANG, Z. X; DONG, H; BELL, T et al.Surface & coatings technology. 2006, Vol 200, Num 18-19, pp 5237-5244, issn 0257-8972, 8 p.Article

Effect of UV irradiation on the surface Gibbs energy of T16A14V and thermally oxidized Ti6A14VPACHA-OLIVENZA, M. A; GALLARDO-MORENO, A. M; MENDEZ-VILAS, A et al.Journal of colloid and interface science. 2008, Vol 320, Num 1, pp 117-124, issn 0021-9797, 8 p.Article

Comparison of dry sliding friction and wear of Ti6A14V alloy treated by plasma electrolytic oxidation and PVD coatingCESCHINI, L; LANZONI, E; MARTINI, C et al.Wear. 2008, Vol 264, Num 1-2, pp 86-95, issn 0043-1648, 10 p.Article

The influence of microstructural characteristics and contaminants on the mechanical properties and fracture topography of low cost Ti6A14V alloyBOZIC, Dusan; SEKULIC, Danijela; STASIC, Jelena et al.International journal of materials research. 2008, Vol 99, Num 11, pp 1268-1274, issn 1862-5282, 7 p.Article

Sol-gel and precursor-derived coatings with cover function on medical alloysHOFFMANN, Bettina; FELDMANN, Martina; ZIEGLER, Giinter et al.Journal of material chemistry. 2007, Vol 17, Num 38, pp 4034-4040, issn 0959-9428, 7 p.Article

Coatings on Ti6Al4V as palliatives for fretting fatigue in cryogenic environmentCARON, I; GRAS, R; GANNE, T et al.Tribology international. 2006, Vol 39, Num 10, pp 1045-1051, issn 0301-679X, 7 p.Conference Paper

A study of the potentials achieved during mechanical abrasion and the repassivation rate of titanium and Ti6A14V in inorganic buffer solutions and bovine serumCONTU, F; ELSENER, B; BÖHNI, H et al.Electrochimica acta. 2004, Vol 50, Num 1, pp 33-41, issn 0013-4686, 9 p.Article

Deposition of Ti-6Al-4V using a high power diode laser and wire, Part II : Investigation on the mechanical propertiesSUI HIM MOK; GUIJUN BI; FOLKES, Janet et al.Surface & coatings technology. 2008, Vol 202, Num 19, pp 4613-4619, issn 0257-8972, 7 p.Article

Effect of ceramic conversion surface treatment on fatigue properties of Ti6A14V alloyLI, C. X; HORSPOOL, D; DONG, H et al.International journal of fatigue. 2007, Vol 29, Num 12, pp 2273-2280, issn 0142-1123, 8 p.Article

The effect of treatment condition on boost diffusion of thermally oxidised titanium alloyZHEN XUE ZHANG; HANSHAN DONG; BELL, Thomas et al.Journal of alloys and compounds. 2007, Vol 431, Num 1-2, pp 93-99, issn 0925-8388, 7 p.Article

Experimental and numerical analysis of local and global plastic behaviour in fretting wearDICK, T; PAULIN, C; CAILLETAUD, G et al.Tribology international. 2006, Vol 39, Num 10, pp 1036-1044, issn 0301-679X, 9 p.Conference Paper

Triode plasma nitriding and PVD coating : A successful pre-treatment combination to improve the wear resistance of DLC coatings on Ti6Al4V alloyAVELAR-BATISTA, J. C; SPAIN, E; FUENTES, G. G et al.Surface & coatings technology. 2006, Vol 201, Num 7, pp 4335-4340, issn 0257-8972, 6 p.Conference Paper

Influence of adiabatic shear bands intersection on the ballistic impact of Ti―6A1―4V alloys with three microstructuresKAI SUN; XIAODONG YU; CHENGWEN TAN et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2014, Vol 606, pp 257-267, issn 0921-5093, 11 p.Article

In Situ Characterization of NiTi/Ti6Al4V Joints During Reaction-Assisted Diffusion Bonding Using Ni/Ti Multilayers : Joining and Interface DesignCAVALEIRO, A. J; RAMOS, A. S; BRAZ FERNANDES, F. M et al.Journal of materials engineering and performance. 2014, Vol 23, Num 5, pp 1625-1629, issn 1059-9495, 5 p.Conference Paper

Determining the stress―strain behaviour at large strains from high strain rate tensile and shear experimentsPEIRS, J; VERLEYSEN, P; VAN PAEPEGEM, W et al.International journal of impact engineering. 2011, Vol 38, Num 5, pp 406-415, issn 0734-743X, 10 p.Article

Unlubricated gross slip fretting wear of metallic plasma-sprayed coatings for Ti6A14V surfacesHAGER, C. H; SANDERS, J. H; SHARMA, S et al.Wear. 2008, Vol 265, Num 3-4, pp 439-451, issn 0043-1648, 13 p.Article

Gross slip fretting wear of CrCn, TiAlN, Ni, and CuNiIn coatings on Ti6A4V interfacesHAGER, C. H; SANDERS, J; SHARMA, S et al.Wear. 2007, Vol 263, Num 1-6, pp 430-443, issn 0043-1648, 14 p.Conference Paper

Effect of microstructure on adiabatic shear band bifurcation in Ti-6A1-4V alloys under ballistic impactKAI SUN; XIAODONG YU; CHENGWEN TAN et al.Materials science & engineering. A, Structural materials : properties, microstructure and processing. 2014, Vol 595, pp 247-256, issn 0921-5093, 10 p.Article