Physical modelling of transport phenomena in a delta-shaped, four-strand tundish with flow modifiersKIM, Hyoung B; ISAC, Mihaiela; GUTHRIE, Roderick I. L et al.Steel research international. 2005, Vol 76, Num 1, pp 53-58, issn 1611-3683, 6 p.Article

Fluid Flow and Mechanisms of Momentum Transfer in a Six-Strand TundishESPINO-ZARATE, Aaron; MORALES, Rodolfo D; NAJERA-BASTIDA, Alfonso et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2010, Vol 41, Num 5, pp 962-975, issn 1073-5615, 14 p.Article

Factors influencing the effectiveness of tundish metallurgy. Pt. 5 = Groessen fuer die Beeinflussung der Wirksamkeit der Verteilermetallurgie. T. 5TSUBOKURA, J; SOMMERVILLE, I.D; MCLEAN, A et al.1985, Vol 12, Num 9, issn 0097-8388, 44, 46Article

Numerical and Physical Modeling of Steel Flow in a Two-Strand Tundish for Different Casting ConditionsBRAUN, Alexander; WARZECHA, Marek; PFEIFER, Herbert et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2010, Vol 41, Num 3, pp 549-559, issn 1073-5615, 11 p.Article

Ladle Shroud as a Flow Control Device for Tundish OperationsMORALES-HIGA, Ken; GUTHRIE, R. I. L; ISAC, M et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2013, Vol 44, Num 1, pp 63-79, issn 1073-5615, 17 p.Article

Perspectives on tundish metallurgy = Aussichten zur VerteilermetallurgieTOLVE, P; PRAITONI, A; RAMACCIOTTI, A et al.Steel times. 1987, Vol 215, Num 3, issn 0039-095X, 128-129, 131-132, 134Article

Optimization of a Six-Strand Continuous Casting Tundish: Industrial Measurements and Numerical Investigation of the Tundish ModificationsMERDER, Tomasz; WARZECHA, Marek.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2012, Vol 43, Num 4, pp 856-868, issn 1073-5615, 13 p.Article

Experimental validation of flow and tracer-dispersion models in a four-strand billet-casting tundishKUMAR, Anil; MAZUMDAR, Dipak; KORIA, Satish C et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2005, Vol 36, Num 6, pp 777-785, issn 1073-5615, 9 p.Article

Numerical and physical simulation of flow patterns in a swirling flow tundishQINFU HOU; ZONGSHU ZOU.Steel research international. 2005, Vol 76, Num 10, pp 726-730, issn 1611-3683, 5 p.Article

A review of continuous casting tundish technologyPARRY, A.V; COURTENAY, J.H.Steel times. 1984, Vol 212, Num 2, issn 0039-095X, 68, 70-72Article

Increase of service life of tundish refractory liningSOKOLOV, A.A; POL'SHCHA, A.F; SOKOLOV, G.E et al.Metallurg. 1983, Vol 28, Num 9, pp 27-28, issn 0026-0827Article

Hydraulics and Mathematics Simulation on the Weir and Gas Curtain in Tundish of Ultrathick Slab Continuous Casting : Advances in Materials and Processing TechnologiesDENGFU CHEN; XIN XIE; MUJUN LONG et al.Metallurgical and materials transactions. B, Process metallurgy and materials processing science. 2014, Vol 45, Num 2, pp 392-398, issn 1073-5615, 7 p.Article

Behavior of Mixed Grade during the Grade Transition for Different Conditions in the Slab Continuous CastingALIZADEH, Mehdi; EDRIS, Hossein; AHMAD REZA PISHEVAR et al.ISIJ international. 2008, Vol 48, Num 1, pp 28-37, issn 0915-1559, 10 p.Article

Large eddy simulation on flow structure in centrifugal flow TundishWANG, Fang; LI, Baokuan; TSUKIHASHI, Fumitaka et al.ISIJ international. 2007, Vol 47, Num 4, pp 568-573, issn 0915-1559, 6 p.Article

The use of the LSHR sampler to determine total oxygen contents in the ladle and tundish for different steel gradesHANSEN, Thorbjörn; RUNNSJÖ, Gunilla; SUNDQVIST, Olle et al.Steel research international. 2006, Vol 77, Num 8, pp 550-557, issn 1611-3683, 8 p.Article

Improvement of melt mixing and cleanness in ladle, tundish and mould by application of advanced simulation techniquesHARLOFF, Alexander; PüTZ, Oliver; RÖDL, Sigurd et al.Steel research international. 2005, Vol 76, Num 1, pp 13-21, issn 1611-3683, 9 p.Article

Tundish aisle conversion at DofascoMOORE, R. C.Iron & steelmaker. 1998, Vol 25, Num 6, pp 39-41, issn 0275-8687Conference Paper

Thermal analysis of metal vessel systems for continuous steel castingZHARNITSKII, M. D.Russian journal of heavy machinery. 1994, Num 11, pp 26-30, issn 1068-3720Article

Modifications apportées aux répartiteurs des coulées continues d'ARBED Esch-Schifflange = Modifications made to the continuous casting tundishes at ATBED-SchifflangePETESCH, J.Revue de métallurgie (Paris). 1984, Vol 81, Num 10, pp 761-766, issn 0035-1563Article

Analysis of Melt Flow in Metallurgical Vessels of Steelmaking ProcessesLEKAKH, Simon N; ROBERTSON, David G. C.ISIJ international. 2013, Vol 53, Num 4, pp 622-628, issn 0915-1559, 7 p.Article

Fluid flow and mixing of melt in steelmaking tundishes = Stroemung und Vermischung der Schmelze in Zwischenpfannen fuer StahlSAHAI, Y; AHUJA, R.Ironmaking & steelmaking. 1986, Vol 13, Num 5, pp 241-247, issn 0301-9233Article

Use of refractories for multistream pouring of steelKISELEV, V.I; OVCHINNIKOV, N.A; SEREBRENNIKOV, G.P et al.Ogneupory. 1986, Vol 8, issn 0369-7290, 57Article

Simple tundish mixing model of continuous casting during a grade transitionCHO, Myung Jong; KIM, In Cheol.ISIJ international. 2006, Vol 46, Num 10, pp 1416-1420, issn 0915-1559, 5 p.Article

Comparison between standard and renormalization group k-ε models in numerical simulation of swirling flow tundishHOU, Qinfu; ZOU, Zongshu.ISIJ international. 2005, Vol 45, Num 3, pp 325-330, issn 0915-1559, 6 p.Article

New insulation concept for steelmaking ladle-tundish systemsPALCO, S; FRECHETTE, M.-H; RIGAUD, M et al.Interceram. 2004, pp 58-61, issn 0020-5214, 4 p., NSArticle